Released 2006 Reviewed: 26 October 2026

DJM-800, field manual

Pioneer DJ DJM-800 four channel DJ mixer, top view

Booth briefing. The DJM-800 is a four channel digital club mixer built around about 50 effects, split between per-channel Sound Color Effects and BPM-synced Beat Effects. Its support page is archived, with no firmware or driver downloads and no macOS compatibility notice of any kind. Most "no sound" reports on this mixer trace to one of three rear-panel switches, not a fault: MASTER ATT, the DIGITAL input selectors, or BOOTH's own MIC SIGNAL switch.

Fast Lane

DJM-800: equipment profile

Four channels with Sound Color Effects built into the mixer rather than bolted on afterwards. This is the mixer this site's own brand history names as the one that "settled it": the feel promoters and rental companies started writing into riders, making the four-channel Pioneer rig the booth's default for years after.

Channels and effects
Four-channel digital mixer, 96 kHz sampling, 24-bit A/D-D/A, about 50 effects across Sound Color Effects (per-channel filter/crush/sweep) and Beat Effects (delay, echo, reverse delay, pan, trance, synced to BPM).
Ports
3x phono, 4x line/CD, 1x line (RCA), 2x mic (XLR/phone), 4x digital coaxial in, master out (XLR+RCA), booth, rec, send, digital coaxial out, MIDI out, phones.
Dimensions and weight
32 cm wide, 38.1 deep, 10.8 tall (12.6 × 15 × 4.3 in). 7.5 kg / 16.5 lb.
Released
2006

The five things that decide your gig

The DJM-800 at a glance, each point linked to its section.

A rear-panel attenuator switch is a common, invisible cause of "no sound."

A rear panel MASTER ATT switch can cut output level by 12 dB or more. A channel that works but a master output that sounds unusually quiet is the signature of this switch being set wrong, before anything else is worth checking.

No sound, or the sound is unusually quiet

Fader start needs the control cable and the analogue cable connected, both.

Fader start with a CD player needs both the CONTROL cable and the analogue input connectors in place together; the control cable alone, or the analogue cable alone, is not enough.

Fader start is not working with a CD player

The DIGITAL/CD and DIGITAL/LINE selectors have to match what is actually plugged in.

Rear panel DIGITAL/CD and DIGITAL/LINE input selector switches have to match whatever is actually connected. Set wrong, the symptom reads as "no sound" or "no digital output," not as a switch problem.

No sound, or the sound is unusually quiet

BOOTH output has its own mic switch, separate from the main mix.

The BOOTH output has its own MIC SIGNAL switch on the rear panel, separate from the main mix. Set to CUT, it removes the microphone from the booth output specifically while the mic stays audible in the main mix.

Effects, EQ and MIDI

About 50 effects, split across two families with different behaviour.

About 50 effects split across two families with different behaviour: Sound Color Effects run per channel (filter, crush, sweep); Beat Effects are BPM-synced (delay, echo, reverse delay, pan, trance). Each has its own Level/Depth dial.

Effects, EQ and MIDI

Official equipment video

Note: This feature requires an internet connection.

If something goes wrong

No sound, or the sound is unusually quiet

Short answer. Check, in order: the input selector is set to the component actually playing, the rear panel DIGITAL/CD or DIGITAL/LINE selector matches the connected gear, cables are seated and not loose, connectors are not dirty, and the rear panel MASTER ATT switch is not set to -12 dB or similar.

The switch most people miss. A rear panel MASTER ATT switch can cut output level by 12 dB or more. A channel that works but a master output that sounds unusually quiet is the signature of this switch being set wrong, before anything else is worth checking.

Fader start is not working with a CD player

Short answer. Fader start with a CD player needs both the CONTROL cable and the analogue input connectors in place together; the control cable alone, or the analogue cable alone, is not enough.

Fix it now. Confirm the FADER START button is set to ON, then check both connections, not just one.

The microphone is not heard on booth monitors

Short answer. The BOOTH output has its own MIC SIGNAL switch on the rear panel, separate from the main mix. Set to CUT, it removes the microphone from the booth output specifically while the mic stays audible in the main mix.

Why it matters. A DJ who cannot hear themselves on booth monitors despite a working mic, with the main room hearing it fine, should check this switch before assuming a cable fault.

An effect does not seem to do anything

Short answer. Confirm the effect channel selector points at the channel actually meant to be affected, and that the parameter 2 dial (LEVEL/DEPTH) is not sitting at MIN.

BPM will not measure, or the reading looks wrong

Short answer. BPM measurement needs the TRIM dial on each channel set so the input level sits near 0 dB on the channel meter; an over or under driven signal is the most common cause of a BPM that will not measure. Some tracks will not measure reliably regardless; TAP sets BPM by hand instead. A BPM reading that differs from the value printed on a CD is a difference in measurement method, not a fault.

A MIDI sequencer will not sync

Short answer. MIDI out for syncing an external sequencer, which has to be set to slave mode and support MIDI timing clock to work with this mixer. A sequencer that does not support MIDI timing clock cannot sync to this mixer, whatever is changed on the DJM-800 itself.

Features and specifications

Effects, EQ and MIDI

What it is. a four channel digital club mixer built around roughly 50 effects split across Sound Color Effects and Beat Effects, the mixer this site’s own brand history names as the one that settled the four channel Pioneer DJ booth standard.

Effects. About 50 effects split across two families with different behaviour: Sound Color Effects run per channel (filter, crush, sweep); Beat Effects are BPM-synced (delay, echo, reverse delay, pan, trance). Each has its own Level/Depth dial.

Signal path. 96 kHz sampling with 24 bit A/D and D/A converters.

EQ. A 3 band EQ isolator on each channel.

MIDI. MIDI out for syncing an external sequencer, which has to be set to slave mode and support MIDI timing clock to work with this mixer.

Digital input selection. Rear panel DIGITAL/CD and DIGITAL/LINE input selector switches have to match whatever is actually connected. Set wrong, the symptom reads as "no sound" or "no digital output," not as a switch problem.

Dimensions, weight and power

Width: 320 mm / 12.6 in

Height: 108 mm / 4.25 in

Depth: 381 mm / 15 in

Weight: 7.5 kg / 16.5 lb

Power. Power supply 220-240 V AC, 50/60 Hz. Power consumption 30 W, per its own Operating Instructions manual.

Sources. Pioneer DJ's own Operating Instructions manual for dimensions, weight and power.

Firmware, drivers and manuals

What Pioneer DJ do and do not say about its future

Short answer. Pioneer DJ’s support page for this model is marked "Archived." Unlike its sibling the DJM-750, this model’s support page makes no mention of macOS compatibility checking of any kind, and no firmware or driver downloads are listed on it at all.

No firmware, no driver. This is a fully analogue-control mixer. No firmware version or update history for the DJM-800 could be found anywhere, including on its own archived support page, and none is listed to download.

Pioneer DJ's DJM-800 product page →

Frequently asked questions

Quick answers

Is the DJM-800 discontinued?
Its support page is archived, but Pioneer DJ’s support page for this model is marked "Archived." Unlike its sibling the DJM-750, this model’s support page makes no mention of macOS compatibility checking of any kind, and no firmware or driver downloads are listed on it at all.
Is there a firmware update for it?
No. It is a fully analogue-control mixer; none was ever published.
Does it need a driver?
No. None is listed on its support page.
Why is there no sound, or very quiet sound?
A rear panel MASTER ATT switch can cut output level by 12 dB or more. A channel that works but a master output that sounds unusually quiet is the signature of this switch being set wrong, before anything else is worth checking.
What effects does it have?
About 50 effects split across two families with different behaviour: Sound Color Effects run per channel (filter, crush, sweep); Beat Effects are BPM-synced (delay, echo, reverse delay, pan, trance). Each has its own Level/Depth dial.
How much does it weigh?
7.5 kg / 16.5 lb.
What is its power consumption?
Power supply 220-240 V AC, 50/60 Hz. Power consumption 30 W, per its own Operating Instructions manual.
When was it released?
2006.

Looking for the predecessor? See the DJM-700. More legacy Pioneer DJ equipment: the full archive index.

Playing soon and it is not working?

Start Emergency Mode

Where this sits in the line

Pioneer DJ All brands Knowledge base FAQ and Fixes Dictionary

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Pioneer DJ's current archived DJM-800 product page, its archived support page, and its own Operating Instructions manual (specifications and troubleshooting tables read directly), checked 26 October 2026. Specifications theirs, priorities ours.