Booth briefing. The TORAIZ AS-1 is a monophonic analogue synthesizer in Pioneer DJ's TORAIZ range, made for professional and aspiring producers, in the studio and on stage. Pioneer DJ built it working closely with Dave Smith, on the same analogue filters as his Prophet-6 synthesizer. A touch slider manipulates seven different parameters in performance, and a 64-step sequencer and an arpeggiator drive patterns. It plays one note at a time, so beside the decks it is a bassline, a lead or a drone played live, rather than another deck.
Fast Lane
TORAIZ AS-1: equipment profile
A monophonic analogue synthesizer with the filter circuit of the Prophet-6, from Pioneer DJ's TORAIZ range.
- What comes out
- AUDIO OUT L and R on quarter-inch TS jacks. PHONES on a quarter-inch stereo jack. TRIGGER IN on a quarter-inch TS jack.
- Staying in time
- MIDI IN and MIDI OUT/THRU on 5-pin DIN, and MIDI over USB. MIDI Clock Mode: Off, Master, Slave, Slave Thru, Slave No S/S.
- Computer and driver
- USB Type-B port. Driver and companion app: N/A.
- Power
- The included AC adaptor only, DC 5 V at 2 A, 1,500 mA drawn. No battery or USB bus power described.
- Dimensions and weight
- 26.7 cm wide, 17.8 deep, 6.9 tall (10.5 × 7 × 2.7 in). 1.4 kg / 3.1 lb.
- Released
- 2017
The TORAIZ AS-1 Operating Instructions DRI1434A and the Quick Start Guide DRH1418C, which is where its dimensions and weight live.
The five things that decide your gig
The TORAIZ AS-1 in five points, each linked to its section.
It is analogue, so let it warm up before you trust the tuning.
Calibrate again in any room it has not been in.
Keep your hands off the keys and the slider when you switch it on.
Notes sound that nobody pressed.
Lit buttons and a blank display is not a dead unit.
Touching any control is the first test.
Sequencer will not follow another machine? Check MIDI Clock Mode.
Following another machine needs a Slave setting.
The sound jumps when you touch a knob after changing program.
Pot Mode decides whether it jumps.
Official equipment video
Note: This feature requires an internet connection.
What to watch for
Warm-up and Calibrate
Short answer. The TORAIZ AS-1 is analogue, so its pitch and filter cutoff drift with air temperature and supply voltage, and the manual says to leave the unit on for about 10 to 20 minutes before relying on it. It then asks you to run Calibrate from the GLOBAL SETTING menu once it is warm, to repeat that over several days in the room the unit will live in, and to repeat it before using the unit somewhere unusual, such as on stage. A synth that is slightly out of tune ten minutes after switching on is behaving as documented.
The keyboard that plays by itself
Short answer. The AS-1 keyboard is an electrostatic touch surface, and its sensitivity is calibrated every time the unit powers up. The manual's consequence is specific: if a key or the slider is being touched when the rear power button is pressed, the keyboard can come up unstable, with notes sounding on keys nobody is touching, or only a narrow range of the keys sounding. The fix is to switch off and on again with your hands clear of the keys and the slider.
Compatibility and setup
Clock and sync
Short answer. If the AS-1 sequencer or arpeggiator will not run from its own clock, MIDI Clock Mode in the GLOBAL SETTING menu is the first thing to check: it has to be Master or Off. If it should follow another machine, the MIDI cable has to run from that machine's MIDI OUT to the AS-1 MIDI IN, that machine has to be sending clock as master, and MIDI Clock Cable has to name the connector the clock arrives on, the MIDI port or USB. Slave Thru passes the received clock on to MIDI OUT/THRU, and Slave No S/S ignores start and stop.
Power, and the cord hook
Short answer. The TORAIZ AS-1 runs from the included AC adaptor, DC 5 V at 2 A, and draws 1,500 mA. The manual describes no battery and no USB bus power: the USB Type-B port is the computer connection for MIDI. Hook the adaptor lead on the rear cable hook before you start, because the manual says the sound stops abruptly if it is pulled while you play. The power button does not isolate the unit from the supply, and the manual says to unplug the cord to shut it down completely.
Dimensions and weight
Width: 267.4 mm / 10.53 in
Height: 68.6 mm / 2.7 in
Depth: 177.7 mm / 7 in
Weight: 1.4 kg / 3.1 lb
Sources. Pioneer DJ's own documentation, document DRH1418C, for width, height, depth and weight.
If something goes wrong
Lit buttons, blank display
Short answer. A TORAIZ AS-1 with lit buttons and a blank display has documented causes. The screen saver is running, and touching any control brings the display back. The unit was switched on while a button other than the power button was held down, and the fix is to switch off and on again touching nothing. And when MIDI Clock Mode is set to a Slave setting with no clock arriving, the manual notes that the TAP button goes out and the screen saver can take over the display.
Features, tips and maintenance
Why the sound jumps
Short answer. Every program on the AS-1 stores where its knobs were, and the physical knobs do not follow. After changing programs the control on the panel no longer matches the saved value, and with the default Pot Mode of Jump, touching a control makes the sound leap to wherever the knob happens to sit. The GLOBAL SETTING menu offers two other behaviours: Relative, where the knob moves the value from where it was, and Passthru, where nothing changes until the knob crosses the stored value. Passthru is the one least likely to produce a sudden jump on a stage.
What the firmware record says
There is no firmware for the TORAIZ AS-1. Its help centre page lists the manual, two quick start guides and a power supply addendum, and has no firmware section.
What the manual does say. The unit uses SysEx messages for system updates and for sending and receiving programs, but no system update is listed to download. That is an absence of publishing, recorded as such, not research we have not done.
Official documentation. Pioneer DJ's help centre page for this model →
Found an entry we have missed? Tell us and we will add it.
Taking one to a gig
Switch it on early. Not when the doors open.
Hands clear at power-on. Put it on a stable surface, press the rear power button, then touch the keys.
Secure the power lead first. The reason is under Power, and the cord hook.
Set Pot Mode before you leave. The choices are described under Why the sound jumps.
Firmware, drivers and manuals
Official downloads and documents
Go to Pioneer DJ for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
Manuals. Official Pioneer DJ manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Does the TORAIZ AS-1 need a warm-up?
- Yes. Warm it up, then run Calibrate.
- Why does the keyboard play notes nobody is pressing?
- A key or the slider was touched at power-on. Switch off and on again.
- Why are the buttons lit but the display blank?
- The screen saver, or a button held at power-on.
- Can it run on batteries or USB power?
- No, mains only, through the AC adaptor. USB carries MIDI and nothing else.
- Why does the sound jump when I touch a knob?
- Pot Mode defaults to Jump. The other two choices are Relative and Passthru.
- Is there a firmware update for it?
- No. There is none for it.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Pioneer DJ All brands Knowledge base FAQ and Fixes Dictionary
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Pioneer DJ's TORAIZ AS-1 Operating Instructions DRI1434A, read in full, with the quick start guide DRH1418C and the help centre page for the power supply addendum, checked 18 October 2026. Specifications theirs, priorities ours.