Released 2020 Reviewed: 22 October 2026

MASCHINE+, field manual

Native Instruments MASCHINE+ standalone groovebox, top view

Booth briefing. MASCHINE+ is the standalone groovebox and sampler in Native Instruments' MASCHINE production line, announced in September 2020, and the one MASCHINE that runs without a computer. It has its own processor, memory and storage, and the same pad and knob layout as the full-size MK3. A one-off setup over Wi-Fi with a Native ID registers it, and after that it works on its own. It can also act as a controller for MASCHINE on a computer, the way the MK3 does.

Fast Lane

MASCHINE+: equipment profile

A standalone groovebox and sampler in the MASCHINE line, with a quad-core processor, RAM and storage of its own.

Without a computer
Yes. Quad-core processor, 4 GB of dual-channel DDR3L RAM.
Drives and cards
32 GB internal eMMC and a 64 GB SD card.
What comes out
Audio interface at 44.1 kHz / 24-bit, or 96 kHz / 24-bit in controller mode.
Power
Included power supply with a lockable connector, or USB bus power in controller mode.
Released
2020

The five things that decide your gig

MASCHINE+ in five points, each linked to its section.

Runs without a computer, genuinely.

Neither the MK3 nor MIKRO can play a pattern without a laptop.

What "no computer necessary" actually means

Setup needs Wi-Fi and a Native ID.

Until it is registered, the computer-free claim does not apply.

What "no computer necessary" actually means

Two sample rates are quoted for the audio interface.

The maker's own page gives both figures.

What comes out, and what goes in

It needs its own power supply to run alone.

Pack the power brick, not just a USB cable.

What feeds it

Storage is internal, SD card and USB.

The card slot is how the library grows.

What "no computer necessary" actually means

Official equipment video

Note: This feature requires an internet connection.

Connections and setup

What "no computer necessary" actually means

Short answer. MASCHINE+ runs without a computer, genuinely, on a quad-core processor with 4 GB of dual-channel DDR3L RAM and its own storage. Native Instruments' line is direct: "No computer necessary."

The claim starts after initial setup, not before it. Registering the unit needs a wireless internet connection and a Native ID the first time. Once that is done it operates entirely on its own.

Storage: 32 GB internal eMMC holds the OS and factory content. The included SD card ships at 64 GB and the slot supports up to 1 TB; two USB ports can add external drives for larger libraries. The factory library is the MASCHINE+ Selection at 24 GB.

It can also act as a controller. In controller mode it runs USB-powered from a computer, the same role the MK3 plays.

What comes out, and what goes in

Short answer. 2 x ¼" TRS line outputs, 2 x ¼" TRS line inputs, one ¼" dynamic mic input, one stereo headphone output, MIDI In and Out, and a footswitch input for start/stop, record, and sustain/expression detection.

Two different sample rates are given for the same interface. The specification table gives 44.1 kHz / 24-bit, or 96 kHz / 24-bit in controller mode; the feature section on the same page describes it as 96 kHz / 24-bit with no qualifier. Verify against the actual unit if the figure matters to a session.

Two colour displays at 480 x 272. Its own panel, rather than the MK3's pair of high-resolution screens.

Wi-Fi and Ableton Link. Wi-Fi handles setup and registration; Ableton Link gives tempo sync with other networked gear.

What to watch for

What feeds it

Short answer. MASCHINE+ needs its included power supply, which has a lockable connector, to run standalone. In controller mode USB bus power is enough.

322 x 301 x 51 mm (W x D x H), 2.50 kg. Close to the MK3's footprint, but thicker and about 300 g heavier.

Professional tips

Worth knowing before the gig

Register it at home. Wi-Fi and a Native ID are needed once, so do it before the gig rather than at the venue.

Carry a spare card for a long session. The factory content can be outgrown, and there is no cloud sync to fall back on.

Firmware, drivers and manuals

Official downloads and documents

Go to Native Instruments for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.

No firmware version, change history or updater could be reached for MASCHINE+, so none is linked here, and no recall or service notice was found for it either.

Manuals. Official Native Instruments manual page →

Broken link? Let us know and we'll fix it.

Frequently asked questions

Quick answers

Does MASCHINE+ run without a computer?
Yes.
Does it need internet at all?
Only for the first setup.
What sample rate does the audio interface run at?
Two figures are published: 44.1 kHz and 96 kHz.
How much storage does it have?
32 GB internal, plus a 64 GB SD card.
How is it powered?
The included supply, or USB in controller mode.
Can it also work as a MASCHINE controller?
Yes, from a computer over USB.
Is there a published firmware version?
None found.
How big is it?
322 x 301 x 51 mm, 2.50 kg.

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Native Instruments' own MASCHINE+ product page, specification page and the ask.audio announcement article, checked 22 October 2026. Specifications theirs, priorities ours.