Booth briefing. The JUPITER-08 is a synthesizer in Roland's Boutique series, announced in October 2026 for the 45th anniversary of the JUPITER-8. It recreates that 1981 polyphonic synth in a compact, battery-powered body and ships with the K-25m keyboard. It plays up to 32 voices, or the original's polyphony when set, with a two-part 64-step sequencer and an arpeggiator. It has a built-in speaker. Next to a mixer it is one stereo source, synced over MIDI, USB or an analogue clock pulse.
Fast Lane
JUPITER-08: equipment profile
A Boutique synthesizer for the JUPITER-8’s 45th anniversary, shipped with the K-25m keyboard.
- Plays
- Up to 32 voices, or the original JUPITER-8’s polyphony, chosen in the Poly Mode setting. Two-part 64-step sequencer and an arpeggiator.
- What comes out
- OUTPUT and PHONES, both stereo 3.5 mm, and MIX IN on 3.5 mm. Built-in speaker.
- Output level
- N/A.
- Staying in time
- MIDI IN and MIDI OUT on five-pin DIN, and EXT CLOCK IN on a mono mini jack. No CV OUT or GATE OUT.
- Computer and driver
- USB-C for audio and MIDI to a computer, with Roland’s driver.
- Power
- Four AA cells or USB bus power (500 mA). About 6 hours on Ni-MH. 1.6 kg with the K-25m and the batteries.
- Dimensions and weight
- 30.8 cm wide, 20.9 deep, 5.4 tall (12.1 × 8.2 × 2.1 in). 1.6 kg / 3.5 lb.
- Released
- 2026
Specifications and update history as Roland publishes them.
JUPITER-08: five things to know
The JUPITER-08 in five points, each linked to its section.
Up to 32 voices, or the original JUPITER-8 polyphony.
Poly Mode decides which, so check it before the set.
Audio leaves on 3.5 mm sockets, so bring the cable.
Pack it with the synth.
It follows and sends clock.
Set Sync Source rather than leaving it on Auto.
USB-C, and only a data cable works.
A charge-only cable looks identical.
One update so far, 1.01, with a real fix.
Below it, Poly Mode can be ignored.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Voices and sound
Short answer. Up to 32 voices, or the original JUPITER-8's polyphony, chosen in the Poly Mode setting.
Poly Mode. orG plays with the original model's maximum polyphony, AdU with this unit's. A patch built in one mode can behave differently in the other when chords overlap.
Sequencer and arpeggiator. A two-part, 64-step polyphonic sequencer with up to eight notes per step and motion recording, plus an arpeggiator. 240 patches and 96 patterns.
Effects. 17 MFX types, four delays and five reverb types including a shimmer mode, all inside the unit.
The K-25m comes in the box. It is a 25-key dock, so the JUPITER-08 is playable out of the box rather than only programmable.
Audio connections
Short answer. On the JUPITER-08, OUTPUT and PHONES are both stereo 3.5 mm sockets, and MIX IN is a third.
Cable. Club mixers take quarter-inch or RCA, so bring your own cable: 3.5 mm to dual quarter-inch, or 3.5 mm to RCA. The same lead covers every Boutique on this hub.
Speaker. It has a small built-in speaker for checking a patch on a table. It is not an output: everything that reaches the mixer still leaves on the 3.5 mm socket.
MIX IN. It lets another source share the outputs, which is how two Boutiques reach one mixer channel. A hot source arriving there raises what the mixer receives without the JUPITER-08's own level moving.
Output level: N/A. Set it at soundcheck, and again after changing patch.
Clock and MIDI
Short answer. MIDI IN and MIDI OUT on five-pin DIN, one EXT CLOCK IN on a mono mini jack, and MIDI over USB.
Sync Source. The sequencer follows the clock chosen in the Sync Source setting: Auto, its internal clock, MIDI or USB. Auto picks up whatever arrives, so set it explicitly when two clocks could reach the JUPITER-08 at once.
It can send clock too. Sync Out sends MIDI clock from the MIDI connector, the USB port or both, so it can lead another machine rather than only follow one.
EXT CLOCK IN takes a pulse, not MIDI. A drum machine's trigger output or a modular clock steps the sequencer with no MIDI in the chain. There is no CV OUT and no GATE OUT.
What the computer needs
Short answer. The JUPITER-08 has a USB-C port carrying audio and MIDI, so one cable to a computer is the whole connection. It needs Roland's own driver, and a real data cable for updating.
A charge-only USB-C cable will not work. Roland's manual says so directly: charge-only cables cannot carry data. It looks identical, and it is the usual reason a computer does not see the unit.
The driver is a separate download from the system program. Roland publish driver 1.0.0 for macOS Sonoma 14 or later and for Windows 11.
USB-C, not micro USB. The older Boutiques on this hub use micro USB, so a bag packed for a JU-06A has the wrong cable.
Power, weight and size
Short answer. The JUPITER-08 runs on four AA cells, Ni-MH or alkaline, or USB bus power at 500 mA. There is no DC input on the connector list.
Roland quote about 6 hours on Ni-MH cells of 1,900 mAh, and no alkaline figure. For a long set, a USB battery pack is the route to rely on.
The published 1.6 kg includes the K-25m keyboard and the four batteries. It ships docked, so that is what goes in the bag.
308 mm wide, 209 mm deep, 54 mm tall with the K-25m. Deeper than a module-only Boutique, so check a case built for one.
Auto Off is 240 minutes by default. A unit left untouched for four hours switches itself off; Auto Off Minute changes it.
What to watch for
Firmware
Short answer. Version 1.01 of October 2026 is the only update, and it carries a real fix.
What 1.01 changed. It fixed the POLY parameter setting not being applied, improved the arpeggiator with Mode set to rnd and Oct to 2 and in Split mode, and improved the behaviour when changing VCO-2 Range.
Check the display. The version shows on the unit's display. A JUPITER-08 below 1.01 can ignore its own POLY setting, which is worth knowing before blaming a patch.
Never compare Roland version numbers across models. A 1.01 here and a 1.01 on another Roland box are unrelated.
Professional tips
Before the gig
Pack the 3.5 mm audio cable and a spare. No venue has one for a Boutique.
Label the USB-C data cable that works. Keep it in the bag with the machine.
Fresh Ni-MH cells or a USB battery pack. The battery figure is Roland's, and it is for Ni-MH only.
Firmware, drivers and manuals
Official downloads and documents
Manuals, drivers and the system program are on Roland's site. The links below go to Roland's own pages, which stay up to date.
Roland publish a Reference Manual and a Quick Start for the JUPITER-08.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- How many voices does the JUPITER-08 have?
- 32 at most. The orG Poly Mode limits it to the original's count.
- Does it come with a keyboard?
- Yes, the K-25m keyboard dock is in the box.
- What cable do I need for the house system?
- 3.5 mm to dual quarter-inch or 3.5 mm to RCA, whichever the mixer inputs take.
- Can it send MIDI clock?
- Yes, over five-pin MIDI, USB or both.
- Does it have CV and GATE outputs?
- No. EXT CLOCK IN is its only analogue socket, and it is an input.
- Which firmware should it be on?
- 1.01, the only update Roland list, which fixes the POLY setting.
- How long does it run on batteries?
- Roughly six hours on Ni-MH, by Roland's figure.
- Why does the computer not see it?
- Usually a charge-only USB-C cable. Use a data cable.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's own JUPITER-08 product and specification pages, the reference manual and the Updates & Drivers page, checked 14 November 2026. Specifications theirs, priorities ours.