Booth briefing. The JU-06A is a synthesizer in Roland's Boutique series, the line of compact, battery-powered recreations of Roland's classic instruments. Roland built it from the best of the JUNO-60 and JUNO-106: the 106's high-pass filter, the 60's envelope-controllable pulse-width modulation, chorus, arpeggio, chord memory and a 16-step sequencer, in two sound modes switched from the front panel. It has four voices, so a four-note chord uses the whole instrument. It runs on batteries and has a built-in speaker. Next to a mixer it is one stereo source, synced over MIDI or an analogue clock pulse.
Fast Lane
JU-06A: equipment profile
A Boutique synthesizer built from the JUNO-60 and JUNO-106, with a built-in speaker.
- Plays
- Four voices, with a 16-step sequencer and an arpeggiator. Two sound modes, 60 and 106, with 64 patches in each.
- What comes out
- OUTPUT and PHONES, both stereo 3.5 mm, and MIX IN on 3.5 mm. Built-in speaker.
- Output level
- N/A.
- Staying in time
- MIDI IN and MIDI OUT on five-pin DIN, and EXT CLOCK IN on a mono mini jack. No CV OUT or GATE OUT.
- Computer and driver
- USB Micro-B for audio and MIDI to a computer, with Roland’s driver.
- Power
- Four AA cells or USB bus power (500 mA). About 6 hours on Ni-MH. 995 g including the batteries.
- Dimensions and weight
- 30 cm wide, 12.8 deep, 4.9 tall (11.8 × 5 × 1.9 in). 1 kg / 2.2 lb.
- Released
- 2019
Specifications and update history as Roland publishes them.
JU-06A: five things to know
The JU-06A in five points, each linked to its section.
Four voices, as on the JUNO-60 and JUNO-106.
A held pad and a running arpeggio compete for them.
No CV OUT and no GATE OUT: this is not the SH-01A.
It cannot drive anything analogue.
Audio leaves on 3.5 mm sockets, so bring the cable.
Pack it with the synth.
One system program, and no change history.
There is no list of fixes to read before the gig.
Updating needs a micro USB data cable.
With the wrong lead the port looks dead.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Voices and sound modes
Short answer. Four voices, two sound modes called 60 and 106, and 64 patches stored in each mode.
Four voices. The JUNO-60 and the JUNO-106 were four-voice instruments and the JU-06A reproduces that. A fifth note takes a voice back from the first.
Arpeggiator and sequencer. Both play into those same four voices. The step sequencer is 16 steps and monophonic, one note per step.
60 and 106. They are separate sound modes with their own patch banks, and they are not the same loudness through the same settings. Switching mode mid-set moves the level at the mixer.
Chord memory and hold. Sixteen chord memories, plus HOLD, CHORD and NOTE buttons in the keyboard section. The optional K-25m keyboard unit is what turns it into something you play rather than something you program.
Audio connections
Short answer. On the JU-06A, OUTPUT and PHONES are both stereo 3.5 mm sockets, and MIX IN is a third.
Cable. Club mixers take quarter-inch or RCA, so bring your own cable: 3.5 mm to dual quarter-inch, or 3.5 mm to RCA. One lead covers the SH-01A, the TB-03, the SE-02 and the VP-03 too.
Speaker. It has a small built-in speaker, which the SH-01A does not. It is enough to check a patch on a table before anything is plugged in. It is not an output: everything that reaches the mixer still leaves on the 3.5 mm socket.
MIX IN. It lets another source share the outputs, which is useful for chaining two Boutiques into one channel at the mixer. A hot source arriving there raises what the mixer receives without the JU-06A's own level moving.
Output level: N/A. Set it at soundcheck, and again after changing patch: a resonant filter near self-oscillation is a different level from the one you set.
Clock and MIDI
Short answer. MIDI IN and MIDI OUT on five-pin DIN, one EXT CLOCK IN on a mono mini jack, and MIDI over USB.
No CV or GATE. EXT CLOCK IN is the only analogue socket. It takes an analogue pulse and follows it, but with no CV OUT and no GATE OUT it cannot send anything analogue. The SH-01A has both and plays a modular voice. The two Boutiques share a chassis and do opposite jobs, and the panels are easy to confuse in a dark booth.
EXT CLOCK IN takes a trigger, not MIDI. A drum machine's trigger output or a modular clock runs the sequencer with no MIDI anywhere in the chain. That is the simplest way to lock a JU-06A to hardware.
What the computer needs
Short answer. The JU-06A has a USB Micro-B port carrying audio and MIDI, so one cable to a computer is the whole connection. It needs Roland's own driver, and a real data cable for updating.
A charging-only micro USB lead will not update it. It looks identical to one that carries data, and it is the usual reason an update refuses to start.
The driver is a separate download from the system program. Roland publish it to 1.0.4 for macOS Sonoma 14 or later and 1.0.1 for Windows 10 and 11, with older builds kept for macOS 10.14 and 10.15, Monterey, Ventura and earlier Windows.
Micro-B, not USB-C. Worth checking against your bag before the day, because the newer Roland boxes have moved on and the cable you reach for first may be the wrong one.
Power, weight and size
Short answer. The JU-06A runs on four AA cells, Ni-MH or alkaline, or USB bus power at 500 mA. There is no DC input on the connector list.
Roland quote about 6 hours on Ni-MH cells. They publish no alkaline figure for this machine. For a long set, a USB battery pack is the route to rely on.
The speaker runs off the same cells. Treat a battery estimate made with the speaker running as optimistic.
The published 995 g includes the four batteries. That is the Boutique convention.
300 mm wide, 128 mm deep, 49 mm tall. Three millimetres taller than the SH-01A and the VP-03, which share its footprint, so measure a tight case built around one of those before the gig.
What to watch for
Firmware
Short answer. Version 1.02 is the only system program, and nothing documents what it changed.
The Updates page carries the download and nothing else. No dated list, no fixes, no added capability. The MIDI Implementation Chart Roland publish for the JU-06A is dated 5 September 2019 at version 1.01, which is the launch version, so 1.02 is the only update this machine has had.
Known issues. None. There is no version floor to plan around. The VP-03 is in that position too; the SH-01A is not, with a muting fault named at 1.06 and a clock change at 1.07.
Never compare Roland version numbers across models. A 1.02 here and a 1.02 on another Roland box are unrelated. Compare the dates if you compare anything.
Professional tips
Before the gig
Mark the case. This synth and the SH-01A share a size and a format, which is how the wrong one gets packed.
Pack the audio cable and a spare. Which cable is under Audio connections.
Label the data cable that works. Keep it in the bag with the machine.
Firmware, drivers and manuals
Official downloads and documents
Manuals, drivers and the system program are on Roland's site. The links below go to Roland's own pages, which stay up to date.
Roland also publish a Sound List and a MIDI Implementation Chart for the JU-06A alongside the owner's manual.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- How many voices does the JU-06A have?
- Four, and no mode adds more.
- Does it have CV and GATE outputs?
- No. EXT CLOCK IN is its only analogue socket, and it is an input.
- Is the JU-06A the same as the SH-01A?
- No. This is a four-voice JUNO with a speaker; the SH-01A is a monophonic SH-101 with CV and GATE outputs and no speaker.
- What cable do I need for the house system?
- 3.5 mm to dual quarter-inch or 3.5 mm to RCA, whichever the mixer inputs take.
- Does it have a built-in speaker?
- Yes, a small one. Fine on a table, no use as a way into the mixer.
- What is the difference between the 60 and 106 modes?
- Each is a separate sound mode with its own 64 patches, and they come out at different levels, so expect a level change when you switch.
- Which firmware should it be on?
- 1.02, the only release Roland list for it.
- Why will the update not start?
- Usually the lead. Try a known data cable before blaming the machine.
- How long does it run on batteries?
- About 6 hours on Ni-MH cells. Alkaline: N/A.
- What does the published weight include?
- 995 g, batteries included.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's own JU-06A product and specification pages, its announcement of 5 September 2019, the owner's manual listing and the Updates & Drivers page, checked 21 October 2026. Specifications theirs, priorities ours.