Released 2017 Reviewed: 17 October 2026

SH-01A, field manual

Roland SH-01A synthesizer, top view

Booth briefing. The SH-01A is a synthesizer in Roland's Boutique series, a recreation of the SH-101, the monophonic synthesizer Roland launched in 1982. Roland models the original circuits with its ACB technology and adds four voices, with Unison, Chord and Poly modes beside Mono, 64 writable patches and 64 sequencer patterns. A CV and gate output lets it drive modular or vintage gear. It is a different machine from the SH-4d, Roland's desktop synthesizer.

Fast Lane

SH-01A: equipment profile

A Boutique reissue of the SH-101, 300 mm wide, with CV and GATE outputs.

What comes out
OUTPUT and PHONES, both stereo 3.5 mm, and MIX IN on 3.5 mm.
Output level
N/A.
Staying in time
MIDI IN and MIDI OUT on five-pin DIN, plus CV OUT, GATE OUT and EXT CLK IN on mono mini jacks.
Computer and driver
USB Micro-B for audio and MIDI to a computer, with Roland’s driver.
Power
Four AA cells or USB bus power (500 mA). About 6 hours on Ni-MH. 965 g including the batteries.
Dimensions and weight
30 cm wide, 12.8 deep, 4.6 tall (11.8 × 5 × 1.8 in). 0.97 kg / 2.1 lb.
Released
2017

Specifications and update history as Roland publishes them.

SH-01A: five things to know

The SH-01A in five points, each linked to its section.

This is the SH-01A, the Boutique, not the SH-4d.

If the audio sockets are quarter-inch, you are holding the SH-4d.

Audio connections

Audio is one 3.5 mm socket, so bring the cable.

The mixer will not have a socket that fits it.

Audio connections

CV OUT, GATE OUT and EXT CLK IN: it can drive a modular.

Pitch and gate leave on their own jacks, not on the audio.

Clock and MIDI

One named fault: a part can go silent mid-sequence.

Roland fixed it in version 1.06.

What Roland has fixed

Updating needs a micro USB data cable.

With the wrong lead the port looks dead.

What the computer needs

Connections and setup

Audio connections

Short answer. The SH-01A has three audio connectors: OUTPUT and PHONES are both stereo 3.5 mm sockets, and MIX IN is a third.

Cable. Club mixers take quarter-inch or RCA, so bring your own cable: 3.5 mm to dual quarter-inch, or 3.5 mm to RCA. The same lead works on the TB-03, the SE-02 and the VP-03.

Which machine is in front of you. This is the SH-01A, 300 mm wide, a Boutique. The SH-4d is 360 mm, has quarter-inch OUTPUT and PHONES, a MIX IN on a mini jack and an EXT CLK IN, and no DC input.

MIX IN lets another source share the outputs. Useful for chaining two Boutiques into one channel at the mixer, and a trap as it is on the SH-4d: a hot source arriving there raises what the mixer receives without this machine's own level moving.

Output level: N/A. Set it at soundcheck, and check it again after a patch change: a resonant filter near self-oscillation is a different level from the one you set.

Clock and MIDI

Short answer. The SH-01A has MIDI IN and MIDI OUT on five-pin DIN, plus CV OUT, GATE OUT and EXT CLK IN on mono mini jacks, and MIDI over USB.

The CV and GATE are outputs. The SH-01A plays an analogue voice: a modular, an old monosynth, anything with a CV and gate input. The SE-02's equivalent block is inputs, so an SH-01A driving an SE-02 is the natural pairing and the cables run one way.

EXT CLK IN takes an analogue pulse. A drum machine's trigger output or a modular clock drives the sequencer without MIDI anywhere in the chain.

USB clock. Taking a MIDI clock over USB needs version 1.07 or later, as set out under What Roland has fixed.

What the computer needs

Short answer. The SH-01A has a USB Micro-B port carrying audio and MIDI. It needs Roland's own driver, and a real data cable for updating.

Roland state that dedicated charging cables cannot be used. A micro USB lead that only carries power looks identical to one that carries data, and it is the usual reason an update refuses to start.

Checking the version is a button sequence. Connect the computer, hold the 1 button and switch on the power; the version screen appears, and you switch off again.

The driver is a separate download from the system program. Roland publish it to 1.0.6 for macOS Sonoma 14 or later and 1.0.1 for Windows 10 and 11.

Power, weight and size

Short answer. The SH-01A runs on four AA cells, Ni-MH or alkaline, or USB bus power at 500 mA. There is no DC input on the connector list.

Roland quote about 6 hours on Ni-MH cells. They publish no alkaline figure for this machine. For a long set, a USB battery pack is the route to rely on.

The published 965 g includes the four batteries. That is the Boutique convention and the opposite of the SH-4d's figure, which excludes them.

300 mm wide, 128 mm deep, 46 mm tall. It shares the chassis with the SE-02 and the VP-03, so a case that fits one fits the others.

What to watch for

What Roland has fixed

Short answer. The SH-01A has one named fault in three releases, and it is the kind that happens while you are playing.

1.06, May 2018. Unintended muting could occur depending on the combination of sequencer playback, the TRANSPOSE switch and sound-production information. In plain terms: a part goes silent mid-sequence, triggered by a control the performer is holding, with the sequencer still running. That reads as a dead machine rather than as a bug.

1.07, January 2019, is the capability floor. USB and MIDI added as MIDI clock sources, soft thru made switchable. Below it the SH-01A cannot take a clock over USB.

1.08, November 2021, changed only the number. Roland attribute it to management-related circumstances with product specifications unaffected.

January 2019 across the Boutiques. The same clock change landed on the TR-09 and TB-03 at their own 1.06 and on the TR-08 at its 1.07, in the same month. Roland's version numbers do not line up across models and their dates do.

Professional tips

Before the gig

Check the version before you borrow one. Neither the muting fault nor the missing USB clock shows on the front panel.

Label the data cable that works. Keep it with the machine.

Pack the audio cable and a spare. Which cable is under Audio connections.

Decide which way the CV runs before you pack. The pairing with the SE-02 is set out under Clock and MIDI.

Firmware, drivers and manuals

Official downloads and documents

Manuals, drivers and the system program are on Roland's site. The links below go to Roland's own pages, which stay up to date.

Roland also host a support document on Windows 10 driver installation and troubleshooting.

Frequently asked questions

Quick answers

Is the SH-01A the same as the SH-4d?
No. This one is the Boutique reissue of the SH-101; the SH-4d is the full-size desktop synthesizer.
Is it called SH-1A?
No. There is no SH-1A in Roland's catalogue.
What cable do I need for the house system?
3.5 mm to dual quarter-inch or 3.5 mm to RCA, whichever the mixer inputs take.
Can it control a modular?
Yes, through CV OUT and GATE OUT. EXT CLK IN goes the other way and lets an analogue pulse drive its sequencer.
Which firmware should it be on?
1.07 or later. 1.08 is the last release published.
Why will the update not start?
Usually the cable: it must be a data lead, not a charging one.
How do I check the version?
With the USB lead connected, hold button 1 while you switch on.
How long does it run on batteries?
About 6 hours on Ni-MH cells, with no alkaline figure. On a long set, run it from USB.
What output level does it run at?
N/A, so the mixer meters are your guide.
What does the published weight include?
965 g, batteries included, unlike the SH-4d's printed figure.

Related synthesizers

Commonly paired with

What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.

Roland All brands Knowledge base FAQ and Fixes Dictionary

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Roland's own SH-01A specification page, the owner's manual and the published update history to version 1.08, checked 17 October 2026. Specifications theirs, priorities ours.