Booth briefing. The SH-4d is a desktop synthesizer in Roland's SH line, the name Roland has used for its core synthesizers since the SH-1000. It has oscillator models that include the SH-101 and JUNO-106, a ladder filter, a multitimbral sequencer with four synth parts and a rhythm part, and up to 60 notes of polyphony. Roland says it suits studio, stage and travel. It runs from USB or batteries and has a clock input and quarter-inch outputs, so it sits on a booth table beside a mixer with ordinary leads.
Fast Lane
SH-4d: equipment profile
The full-size desktop synthesizer, powered by USB or four AA cells.
- What comes out
- OUTPUT (L/MONO, R) and PHONES on quarter-inch jacks. MIX IN on a stereo mini jack. EXT CLK IN on a mono mini jack.
- Output level
- N/A.
- Staying in time
- MIDI IN and MIDI OUT on five-pin DIN. EXT CLK IN takes an analogue clock pulse. MIDI over USB.
- Computer and driver
- USB Type-C for audio and MIDI. No driver from firmware 2.00; Roland's driver below it.
- Power
- USB bus power from a Type-C port (500 mA) or four AA cells. No DC IN. 1,780 g without batteries.
- Dimensions and weight
- 36 cm wide, 19.5 deep, 6.6 tall (14.2 × 7.7 × 2.6 in). 1.78 kg / 3.9 lb.
- Released
- 2023
Roland's site: specifications, owner's manual and update history.
SH-4d: five things to know
The SH-4d in five points, each linked to its section.
No DC input: USB bus power or four AA cells.
Anyone expecting a brick in the bag has nowhere to plug it in.
Outputs are quarter-inch, so no adaptor is needed.
MIX IN is the one socket that does need a small lead.
EXT CLK IN takes an analogue clock pulse, not MIDI.
It fits a hardware rig that is not MIDI-centred.
From firmware 2.00 it needs no driver. Below it, it does.
Check the version before plugging into a stranger's laptop.
One release, 2.00, holds all three fixes.
All three show up while playing, not while loading.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Audio connections
Short answer. Quarter-inch out, a stereo mini jack in, and a mono mini jack for an analogue clock.
Quarter-inch out is the practical advantage over the Boutiques. A booth lead, a stage box or a DI accepts it directly. The TB-03 and the SE-02 put their entire audio output on a 3.5 mm socket and need an adaptor lead that no venue keeps in a drawer.
MIX IN leaves through the same pair. It is a stereo mini jack for putting another source through the SH-4d's outputs, which is useful and is also a trap: a hot source arriving there raises what the mixer receives without the synthesizer's own level moving at all.
Level. N/A. Set it against the booth at soundcheck.
Clock and MIDI
Short answer. Two five-pin DIN MIDI sockets, a separate analogue clock input, and MIDI over USB.
EXT CLK IN. It takes an analogue clock pulse rather than MIDI, so a modular setup, a trigger output or a drum machine's pulse can drive the sequencer with no MIDI anywhere in the chain. The SH-01A and JU-06A have the same input.
Both MIDI directions exist on DIN. The SH-4d can lead or follow, and the cable is the ordinary five-pin lead rather than the SP-404MKII's mini-jack adaptors.
Firmware 2.00 widened what MIDI can do. Patterns can now be changed by an incoming MIDI Program Change rather than only from the Pattern screen, the portamento switch moved onto MIDI CC65, and which MIDI information the machine sends became selectable.
What the computer needs
Short answer. The SH-4d connects over USB Type-C. Whether it needs a driver depends on the firmware version.
2.00 is the cut-off. The 2.00 release notes state "The USB driver now supports Generic", which is Roland's way of saying the machine became class compliant. At 2.00 or above the computer sees it with nothing installed. Below 2.00 the driver is required, and Roland publish it to 1.0.1 for macOS Sonoma 14 or later and 1.0.0 for Windows 10 and 11.
Borrowed units. A machine two years behind, plugged into somebody else's laptop at a venue with no internet, is a machine that produces no audio until a driver downloads. A machine at 2.00 just works.
Updating uses mass-storage mode and the supplied cable. Hold SHIFT while powering on and the SH-4d appears as a drive; the update file is copied to its root, the drive is ejected, and SHIFT starts the update, which takes about three minutes. Roland state that charging cables cannot be used, which is the most common reason it refuses to start.
Power and weight
Short answer. Two ways to run it: a Type-C port at 500 mA, or four AA cells. There is no DC input, so no mains option exists.
No mains adaptor. Unusual on a 1.78 kg desktop synthesizer. It is the MC-101's power situation in a much bigger box.
USB power. 500 mA is undemanding, so a laptop port or any USB battery pack runs the SH-4d for far longer than the cells will. Roland quote about 4 hours on alkalines and about 5 on Ni-MH.
In the box. Four alkaline AA cells and the USB Type-C to Type-A cable are both included, so the machine plays the day it arrives. The published 1,780 g excludes those four cells.
What to watch for
What Roland has fixed
Short answer. The SH-4d has three named faults, cleared by one release, 2.00.
The tone changing by itself. Operating the PATTERN screen or the MIXER screen could change the tone unintentionally, which during a set reads as the machine losing a sound rather than as a screen doing something.
The sequencer running late. Sequencer operation could be delayed when using the DRAWING oscillator model, so the timing problem only appears with one model selected and disappears when you change it, which is the hardest kind of fault to pin down.
Shuffle on an odd number of steps. The shuffle behaved wrongly when the step count was odd. A groove that feels wrong on a 7-step pattern and right on an 8-step one is this.
2.00 is also a large feature release. Alongside those fixes: STEP and HARMONIC added to the oscillator models, a Pattern Chain function, QUICK OVERWRITE for saving a tone or pattern, system-wide delay, chorus and reverb settings, finer SUB STEP timing, undo and redo raised to ten steps, and the class-compliant USB driver described above.
The other two releases carry nothing to act on. 1.03 of April 2023 was a version-number change made for production reasons with specifications unaffected. 1.02 of February 2023 added Voice Reserve and stabilised operation during pattern playback without naming a symptom.
Professional tips
Before the gig
Carry a USB battery pack rather than spare cells. There is no mains route to fall back on.
Get it to 2.00 before you lend it or borrow it. Nobody then has to download a driver at a venue.
Keep the supplied cable with the machine. It is the one that works for the update.
Check the level again after anything goes into MIX IN. See Audio connections.
Firmware, drivers and manuals
Official downloads and documents
Manuals, drivers and the system program are on Roland's site. The links below go to Roland's own pages, which stay up to date.
The SH-4d version of record is 2.00. Roland publish a Quick Start in eight languages and the owner's manual for version 2.00 in English, in HTML and PDF.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Can I run an SH-4d from a mains adaptor?
- No. It has no DC IN socket.
- How long does it last on batteries?
- Between four and five hours, depending on the cells.
- Does it need a driver?
- Only below firmware 2.00. From 2.00 nothing needs installing.
- What cable do I need for the house system?
- An ordinary quarter-inch lead, with no adaptor.
- What is EXT CLK IN for?
- Driving the sequencer from a pulse, with no MIDI involved.
- Which firmware should it be on?
- 2.00, which holds every named fix.
- Why will the update not start?
- Usually the cable: it has to be a data lead, not a charging one.
- What output level does it run at?
- N/A, so the soundcheck decides.
- Can another source play through it?
- Yes, into MIX IN.
- What does the published weight include?
- The machine alone. The cells are extra.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's own SH-4d specification page, its announcement of 23 February 2023, the owner's manual and the published update history to version 2.00, checked 17 October 2026. Specifications theirs, priorities ours.