Booth briefing. The SP-404MKII is a sampler and effects unit in Roland's SP line, the successor to the SP-404A, and Roland calls it the ultimate SP sampler. It has 17 velocity-sensitive RGB pads, an OLED display for editing waveforms, 16 internal projects of up to 160 samples each and 32-voice polyphony. Its effects include Vinyl Simulator and DJFX Looper, and a mic and guitar input adds vocoder and auto pitch. Roland has since added Serato DJ and Serato Studio control by firmware update.
Fast Lane
SP-404MKII: equipment profile
The sampler that replaced the SP-404A, with a DJ MODE and a USB-C port.
- What comes out
- LINE OUT (L/MONO, R) on quarter-inch TRS jacks, impedance balanced. LINE IN on a quarter-inch pair. MIC/GUITAR IN on one quarter-inch jack. PHONES on a quarter-inch and a mini jack.
- Output level
- N/A.
- Staying in time
- MIDI IN and MIDI OUT on stereo miniature (3.5 mm) jacks. MIDI over USB-C.
- Computer and driver
- USB Type-C for audio and MIDI. No driver is listed by Roland.
- Power
- AC adaptor drawing 1,100 mA. USB bus power from a Type-C port rated 1.5 A or more (1,500 mA draw). Six AA cells. 1.1 kg without the adaptor.
- Dimensions and weight
- 17.8 cm wide, 27.6 deep, 7 tall (7 × 10.9 × 2.8 in). 1.1 kg / 2.4 lb.
- Released
- 2021
Roland's site: specifications, manuals and update history.
SP-404MKII: five things to know
The SP-404MKII in five points, each linked to its section.
MIDI is on 3.5 mm mini jacks, so a standard lead does not fit.
Buy the adaptor before the gig.
A 500 mA laptop port will not run it over USB-C.
It reads as a dead unit, not as a power fault.
Audio is quarter-inch in and out.
The outputs are impedance balanced, not balanced.
No driver is needed, and Serato control starts at 5.00.
Nothing to install on a borrowed laptop.
Six of its fixes are the machine stopping.
Be on 5.51 or later.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Audio inputs and outputs
Short answer. Audio is quarter-inch throughout: a TRS pair out, a pair in, one microphone and guitar jack, and headphones in either size.
Impedance balanced is not balanced. Roland use that exact phrase for LINE OUT. It rejects some common-mode noise and it is not a driven balanced output, so a long run to a stage box is still a long run. For a long run, put a DI between the machine and the wall.
Output level: N/A. The channel gets set against the booth at soundcheck. A sampler is harder than a player here, because the level moves with whatever is loaded on the pads: a kick sampled hot and a pad sampled quietly do not arrive at the mixer at the same place.
The MIC/GUITAR jack changes shape with the switch. TRS when it is set for a microphone, standard mono when it is set for a guitar. Same hole, two different cables.
The MIDI sockets, and the cable they need
Short answer. Both MIDI sockets are 3.5 mm stereo miniature jacks. Roland's accessory list names the BMIDI-5-35, BMIDI-1-35 and BMIDI-2-35 adaptor cables, as options sold separately.
What that means on the floor. The five-pin DIN lead that connects everything else in the bag cannot physically go into this machine. There is no adaptor in the box and the cables are Roland part numbers, not something a venue will have in a drawer.
MIDI OUT. The SP-404A has MIDI IN and no MIDI OUT, so it can follow a clock and cannot send one. The SP-404MKII has both, so it can be the clock.
USB-C carries MIDI as well. If the rig is already computer-centred, the one Type-C cable does control and audio together and the mini jacks stay empty.
What the computer needs
Short answer. A USB Type-C port, no driver, and firmware 5.00 or above if the plan involves Serato.
Roland list no driver for this machine. Its Updates and Drivers page carries the system program and an outline data file, and nothing to install on the computer, so audio and MIDI go over USB-C class-compliant.
5.00, April 2025, is the Serato floor. That release is what lets the machine operate Serato DJ and Serato Studio. A unit bought used and left on a 4.x version does not do it, and nothing on the panel says so.
5.50, April 2026, added SDXC cards in exFAT. If a card over 32 GB is refused, the firmware version is the first thing to read rather than the card.
Power and weight
Short answer. Three routes: the AC adaptor, USB-C, or six AA cells.
The 1.5 A requirement. A USB port is only obliged to supply 500 mA, and a hub shares what it has between everything on it. Under the requirement the machine does not switch on. Roland print the figure; nothing on the enclosure does.
The battery figures are short. About 2.5 hours on alkaline AA cells and about 3.5 hours on Ni-MH, against about 4 and 5 hours from the SP-404A on the same six batteries. Batteries are a backup here, not a plan.
1.1 kg, and that figure excludes the adaptor. 177.5 mm wide, 275.8 mm deep, 70.5 mm tall.
What to watch for
What Roland has fixed
Short answer. The SP-404MKII has a long release history, and six entries in it are the machine stopping rather than misbehaving. Three of those six name DJ MODE.
5.51, April 2026. The system may hang during certain operations. Roland do not narrow which, so there is no behaviour to avoid, only a version to be on.
The 4.0x run, 2024 and 2025. A stop while sampling or resampling after importing a sample at 4.05, a stop under certain conditions in DJ Mode at 4.04, and a stop while importing samples from an SD card in DJ Mode at 4.06. Importing several samples at once and getting the same sample repeated was fixed at 4.07.
5.00, April 2025. The unit restarting on certain operations in DJ MODE, fixed in the same release that introduced the Serato control. If a used unit sits below 5.00, that pairing is the argument for updating it.
Other fixes. Roland document roughly a dozen further fixes that a studio user meets and a performer does not, and the version of record, 5.52 of June 2026, is a version-number change made for management reasons with the machine unaffected.
Professional tips
Before the gig
Buy two BMIDI cables and leave them in the bag. One for IN and one for OUT.
Take the AC adaptor even when the plan is USB. It is the only power route with no condition attached. A Type-C port that does not state its current is a port you cannot trust with this machine.
Level it before the set, with the pads you will actually hit. A test tone will not do.
Read the firmware version before you accept a borrowed unit. A unit two years behind looks identical from the front.
Firmware, drivers and manuals
Official downloads and documents
Go to Roland for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
The version of record is 5.52. There is no driver to download; see What the computer needs.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Can I use a normal MIDI cable with an SP-404MKII?
- No, it needs the adaptor cable.
- Why will it not switch on over USB?
- The port supplies less than the 1.5 A it needs, as an ordinary laptop port or a shared hub often does.
- Does it need a driver?
- No, it works class-compliant over USB-C.
- What output level does it run at?
- N/A, so use the samples you will play when you set it.
- Are the outputs balanced?
- Not fully: Roland call LINE OUT impedance balanced.
- How long does it run on batteries?
- Less than the SP-404A manages on the same six batteries, so treat them as the backup.
- Which firmware do I need for Serato?
- 5.00 or later.
- It will not read my SD card. Why?
- Check the firmware version first: exFAT support arrived at 5.50.
- What is the version of record?
- 5.52, but the fix that matters is 5.51.
- Can it be the MIDI clock for my other gear?
- Yes, through the adaptor cable.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's own SP-404MKII product and specification pages, the owner's manuals index and the published update history to version 5.52, checked 17 October 2026. Specifications theirs, priorities ours.