Released 2017 Reviewed: 17 October 2026

SP-404A, field manual

Roland SP-404A sampler, top view

Booth briefing. The SP-404A is a sampler in Roland's SP line, the compact samplers built around the SP-404, and part of the AIRA series. Roland calls it a Linear Wave Sampler. It carries all the functions of the SP-404SX, including 16-bit linear sampling, 12 pads and 29 DSP effects, and ships with an SD card of Loopmasters samples. Roland made it as a companion to the AIRA TR-8 Rhythm Performer, which can trigger it over MIDI, and it also works on its own. Roland describes it as an instrument for DJs, musicians and producers.

Fast Lane

SP-404A: equipment profile

The sampler that came before the MKII, with its own set of connectors.

What comes out
LINE OUT (L, R) and LINE IN (L, R) on RCA phono jacks. PHONES on a stereo quarter-inch jack. MIC IN on a quarter-inch jack.
Output level
N/A.
Staying in time
MIDI IN only. No MIDI OUT, no thru.
Computer and driver
No USB port. Samples load from the SD card slot.
Power
AC adaptor or six AA cells, 450 mA draw. About 5 hours on 1,900 mAh Ni-MH, about 4 on alkalines. 1.2 kg without the adaptor.
Dimensions and weight
17.8 cm wide, 25.7 deep, 7.3 tall (7 × 10.1 × 2.9 in). 1.2 kg / 2.6 lb.
Released
2017

Roland's site: specifications, manuals and the Updates & Drivers page.

SP-404A: five things to know

The SP-404A in five points, each linked to its section.

Audio in and out is RCA, the opposite of the MKII.

Most booths are not wired for it.

Audio connections

MIDI IN only, and no MIDI OUT.

In a rig it must drive, the MKII is the one to bring.

Clock and MIDI

No USB port: samples go in and out on the SD card.

There is no way to load material at the venue.

Getting samples onto it

About five hours on Ni-MH cells.

A working set without mains.

Power, weight and size

There is no firmware version to read on this machine.

So there is nothing to check before the gig.

Firmware

Official equipment video

Note: This feature requires an internet connection.

Connections and setup

Audio connections

Short answer. Line audio goes in and out on RCA, while headphones and microphone use quarter-inch.

Cables. A booth wired for quarter-inch or XLR needs an adaptor lead. The SP-404MKII's leads are quarter-inch and do not carry over, so owning both means two sets of cables.

Unbalanced over a long run picks up the room. RCA has no noise rejection, so keep the run to the mixer short, or put a DI between the machine and the wall.

Level. N/A. Set it at soundcheck and watch it on a channel you can see: an RCA output arriving at a line input is where people reach for gain and find noise instead.

Clock and MIDI

Short answer. MIDI is receive-only: one IN socket on five-pin DIN, nothing to send with.

Clock. Put the clock somewhere else in the rig: a drum machine, a groovebox, a laptop interface. The SP-404A takes the tempo it is given and sends nothing back.

Cable. Five-pin DIN, the lead everything else uses. The MKII moved its MIDI to 3.5 mm mini jacks that need Roland's own adaptor cables, so the newer machine is the awkward one here, not this.

If the sampler has to drive the rig, this is the wrong unit. There is no workaround on the SP-404A.

Getting samples onto it

Short answer. The SD card is the only way in. Roland's connector list for this machine carries no USB port, so there is no computer connection at all.

Driver. None exists. Nothing plugs in, so there is nothing to install.

SD card. Material gets prepared elsewhere and arrives on the card, so pack a spare card and a reader where a cable would otherwise go.

Power, weight and size

Short answer. Mains or six AA cells. Roland's figures are about 5 hours on 1,900 mAh Ni-MH cells and about 4 on alkalines.

Against the MKII. The SP-404MKII manages about 2.5 hours on alkalines and 3.5 on Ni-MH from the same six batteries, so this machine runs about an hour and a half longer on the same cells.

Pack the adaptor anyway. Battery life that covers a set may not cover one that overruns.

Size. 178 mm wide and 257 mm deep. A little heavier than the MKII and a little shallower, and it fits the same corner of a booth shelf.

What to watch for

Firmware

Short answer. The SP-404A has no firmware version, because Roland have issued no system program for it.

Updates and Drivers page. Three items, and none of them is firmware: the SP-404SX Wave Converter for Windows, the same converter for macOS, and the factory sample content that shipped on the included SD card. The converter is for the SP-404SX, a different machine.

What it means. Nothing can be broken by an update. And nothing can be gained from one: a behaviour you dislike on the SP-404A is permanent.

Used units. A used SP-404A is the same machine as a new one. There is no version to ask a seller about, and no state a previous owner could have left it in.

Faults. A fault on the SP-404A is the hardware. With no software to update, a unit that behaves wrongly goes to service.

Professional tips

Before the gig

Pack RCA-to-quarter-inch and RCA-to-XLR leads.

Carry a spare SD card, already loaded. See Getting samples onto it.

Decide where the clock lives before you wire anything. Something else in the rig has to be the master.

Use Ni-MH cells rather than alkalines. The difference is about an hour, at no extra weight.

Firmware, drivers and manuals

Official downloads and documents

The owner's manual and the factory SD card content are on Roland's site. The link below goes to Roland's own page, which stays up to date.

There is no system program and no driver on the SP-404A download page.

Frequently asked questions

Quick answers

What firmware version should an SP-404A be on?
None exists, so there is nothing to check.
Where is the driver for it?
There isn't one, and nothing to install it on.
What is the SP-404SX Wave Converter doing on its download page?
It is for the SP-404SX and does not apply here.
How do I get samples onto it?
Load them onto an SD card elsewhere, then put the card in.
Can it send MIDI clock to my other gear?
No, it can only receive MIDI.
What cables do I need for the house system?
Leads that start at RCA and end in quarter-inch or XLR.
Will my SP-404MKII cables work on it?
Not the audio ones. The MIDI differs too: mini jacks on the MKII, five-pin DIN here.
What output level does it run at?
N/A, so the soundcheck is the only guide.
How long does it run on batteries?
Five hours on Ni-MH cells, four on alkalines, going by Roland's figures.
Is it worth buying used?
Judge it on condition alone, because there is no firmware to compare.

Where this sits in the line

Related samplers

Commonly paired with

What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.

Roland All brands Knowledge base FAQ and Fixes Dictionary

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Roland's own SP-404A product and specification pages, the owner's manuals index and its Updates & Drivers page, checked 17 October 2026. Specifications theirs, priorities ours.