Released 2020 Reviewed: 17 October 2026

DJM-V10-LF, what's different

Pioneer DJ DJM-V10-LF six-channel long-fader mixer control panel, top view

Booth briefing. The DJM-V10-LF is the long-fader version of the DJM-V10 in Pioneer DJ's DJM line: the same six-channel mixer, with the 4-band EQ and the compressor on every channel, built without a crossfader and with longer channel faders in its place. That makes it a mixer for DJs who blend on the channel faders rather than cutting on a crossfader. Its fader curves are drawn for the longer throw, and everything else is shared with the V10, so the DJM-V10 page is the full field manual for connections, effects and troubleshooting.

Fast Lane

DJM-V10-LF: equipment profile

A DJM mixer with PRO DJ LINK and six channels of long faders.

Ports
Six channels: four PHONO sets and six LINE sets on RCA, plus six coaxial DIGITAL IN. MIC1 is a combined XLR and quarter-inch TRS, MIC2 a quarter-inch TRS. Three RETURN sets on quarter-inch TS. Input levels: PHONO -52 dBu at 47 kilohms (-17.8 dBu ceiling), LINE -12 dBu at 47 kilohms (+15 dBu), MIC -57 dBu at 3 kilohms, RETURN -12 dBu at 47 kilohms.
Sound out
MASTER1 on balanced XLR, +6 dBu standard and +25 dBu rated. MASTER2 on RCA, +2 dBu and +21 dBu rated. BOOTH on quarter-inch TRS, +6 dBu and +25 dBu rated. REC OUT on RCA at -8 dBu. Three SEND outputs on quarter-inch TS at -12 dBu. Digital master out is AES/EBU on XLR at 110 ohms. Five-pin DIN MIDI OUT. Four headphone sockets, two quarter-inch and two 3.5 mm, +8 dBu into 32 ohms.
Software
PRO DJ LINK over one 100BASE-TX LINK terminal, and a five-pin MIDI OUT. The sound card runs at 96 kHz with 32-bit conversion on the master and booth outputs and on the channel inputs.
What it unlocks
A six-channel club mixer, not a bundled-software product. A DVS licence comes from the software maker.
What the computer needs
Two USB Type-B ports for two computers, plus a USB Type-A that supplies 5 V at up to 2.1 A for charging. A wired LINK terminal on 100BASE-TX. Sampling at 96 kHz, with signal to noise on USB and DIGITAL IN published at 116 dB.
Power
Mains only, AC 110 V to 240 V at 50 or 60 Hz, 66 W in use and 0.3 W switched off. Power Management is on from the factory: Off mode after 20 minutes with no audio on any channel and no PRO DJ LINK connection, woken with MIDI START/STOP. 12.1 kg, 437.6 mm wide, 467.0 mm deep, 200 g heavier than the standard DJM-V10.
Dimensions and weight
43.8 cm wide, 46.7 deep, 10.8 tall (17.2 × 18.4 × 4.2 in). 12.1 kg / 26.7 lb.
Released
2020

Operating Instructions DRI1643C and the DRH1619C specification tables.

The five things that decide your gig

The DJM-V10-LF in five points, each linked to its section.

No crossfader. If your set depends on one, this is not your mixer.

Check this before the mixer is in the booth, not after.

What's different from the DJM-V10

Channel faders run 60 mm here, not the DJM-V10's 45 mm, on curves drawn for that longer throw.

Worth a few minutes on the actual unit before a gig.

What's different from the DJM-V10

Electronics, I/O and firmware are identical to the DJM-V10.

Everything in the DJM-V10 specification applies unchanged.

What's identical to the DJM-V10

Every connection, FX-routing and documented firmware fix on the DJM-V10 page applies here as written.

For a channel, the send effect or a firmware update, use the DJM-V10 field manual.

Open the DJM-V10 field manual

Its own manual, document DRI1663B, and its own Pioneer DJ support page.

A separate model on paper as well as on the mixer.

Official downloads and documents

Connections, effects, operation and every documented firmware fix: all of it lives on the full field manual, because the DJM-V10-LF runs the same electronics.

Open the DJM-V10 field manual

Compatibility and setup

Product dimensions and weight

Width: 437.6 mm / 17.23 in

Height: 107.9 mm / 4.25 in

Depth: 467 mm / 18.39 in

Weight: 12.1 kg / 26.7 lb

The DJM-V10, for comparison. Same external dimensions, 437.6 × 107.9 × 467 mm / 17.23 × 4.25 × 18.39 in, at 11.9 kg, 200 g lighter than the LF. See the same spec on the DJM-V10 page.

Sources. Pioneer DJ's own DJM-V10-LF manual page, document DRI1663B, read verbatim for width, height, depth and weight.

Features, tips and maintenance

What's different from the DJM-V10

Short answer. Three things, all physical, none electronic: the DJM-V10-LF has no crossfader, its channel faders run 60 mm instead of the DJM-V10's 45 mm, and it weighs 12.1 kg against the DJM-V10's 11.9 kg. Removing the crossfader is what frees the top plate for the longer faders.

Spec DJM-V10 DJM-V10-LF
CrossfaderYesNo (THRU)
Channel fader length45 mm60 mm
Channel fader curvesStandardOwn curves, drawn for the longer throw
Weight11.9 kg12.1 kg
Channels / EQ / compressor6, 4-band, per-channelIdentical
Dimensions (W x D x H)437.6 x 467.0 x 107.9 mmIdentical

Why it matters. A DJ who switches between the two mixers in the same week is moving their hand a genuinely different distance for the same level, on curves that are not the same curves. That is a blend to relearn, not a cosmetic difference.

What's identical to the DJM-V10

Short answer. Everything that is not in the table above. 6 channels, 4-band EQ, a per-channel compressor, dual headphone outputs, booth EQ, the expanded send and return, PRO DJ LINK, MIDI and MULTI I/O. Converters, signal-to-noise, THD and the full I/O list match the DJM-V10 specification line for line.

Why it matters. Nothing in how the DJM-V10-LF routes audio, connects to players, runs effects or responds to a documented firmware fix is specific to this build. The DJM-V10 field manual answers all of it, because it is the same mixer underneath the faders.

Firmware, drivers and manuals

Official downloads and documents

The DJM-V10-LF has its own support page and its own manual, document DRI1663B, separate from the DJM-V10's. Go to Pioneer DJ for the files themselves; we link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.

Manuals. Official Pioneer DJ manual page →

Broken link? Let us know and we'll fix it.

Serato. Serato's hardware page lists the DJM-V10-LF as a paid upgrade: it works with Serato DJ Pro, and HID mode or Serato DVS needs a full Serato DJ Pro licence. Control vinyl or control CDs also need the Serato DVS expansion. All Serato hardware. Serato's DJM-V10-LF page.

Frequently asked questions

Quick answers

Does the DJM-V10-LF have a crossfader?
No. Pioneer DJ confirm it directly: the crossfader is removed and the mixer behaves as a DJM-V10 with the crossfader permanently THRU, so there is nothing missing to troubleshoot.
Why are the DJM-V10-LF's channel faders longer?
The space freed by the crossfader went to 60 mm faders, with curves drawn for that throw.
Is the DJM-V10-LF heavier than the DJM-V10?
Marginally: 12.1 kg against 11.9 kg. Every other dimension is identical.
Can I use the DJM-V10 field manual to troubleshoot the DJM-V10-LF?
Yes. Electronics, I/O and firmware are shared, so the connection, effects-routing and known-issue answers on the DJM-V10 page apply as written.
Is the DJM-V10-LF a different model or a variant?
A separate model, officially, with its own manual (DRI1663B).

Related mixers

Commonly paired with

What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.

Pioneer DJ All brands Knowledge base FAQ and Fixes Dictionary

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Pioneer DJ's DJM-V10-LF instruction manual (DRI1663B) and support pages, and the DJM-V10 field manual this page defers to for everything the two mixers share, checked 17 October 2026. Specifications theirs, priorities ours.