Booth briefing. The TB-03 is Roland's Boutique Bass Line, a descendant of the TB-303 Bass Line Synth, with the same layout and controls. Roland's ACB modelling recreates the 303 sound, with saw and square waveforms, and the TB-03 adds a four-digit LED display, overdrive, delay and reverb, step write, shuffle and fine tempo control. CV and GATE outputs let it play analogue and modular synths, and MIDI and USB let a DAW or other gear play it. It keeps playing a pattern while you switch between write and play modes.
Fast Lane
TB-03: equipment profile
The Boutique reissue of the TB-303, which Roland calls a Bass Line, with a CV output and a GATE output.
- What comes out
- One stereo OUTPUT, PHONES and MIX IN on 3.5 mm. Mono CV OUTPUT and GATE OUTPUT, also 3.5 mm.
- Output level
- N/A.
- Staying in time
- MIDI IN, MIDI OUT and TRIGGER IN. USB as a MIDI clock source from firmware 1.06.
- Computer and driver
- Micro-B USB for audio and MIDI to a computer, with Roland’s driver.
- Power
- Four AA cells or USB bus power (500 mA). About five hours on rechargeables.
- Dimensions and weight
- 30.8 cm wide, 13 deep, 5.2 tall (12.1 × 5.1 × 2 in). 0.94 kg / 2.1 lb.
- Released
- 2016
Roland's own TB-03 specification page and the update history to ver. 1.07.
TB-03: five things to know
The TB-03 in five points, each linked to its section.
Several sockets are the same size and only one is audio.
The wrong socket gives a silent channel.
Audio is one 3.5 mm socket, so bring the cable.
The mixer will not have a socket that fits it.
It has CV and GATE outputs, so it can play other gear.
It plays other gear as well as its own sounds.
Below firmware 1.06 it will not take a clock over USB.
A laptop-led rig will not make it follow the DAW.
It runs on batteries, so it can run out mid-set.
It counts down from the moment you switch it on.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Audio output and cable
Short answer. One stereo OUTPUT jack on 3.5 mm carries the audio. PHONES and MIX IN are the same size, and so are the CV OUTPUT and GATE OUTPUT, which are not audio at all.
The socket trap. Audio, headphones, an audio input and two control-voltage outputs all share one connector size on one small panel. The mixer takes whatever you hand it, and a control voltage arriving on a mixer channel produces nothing. In a dark booth that reads as a broken machine.
The cable you need. Club mixers take quarter-inch or RCA, so bring your own: 3.5 mm to dual quarter-inch, or 3.5 mm to RCA, from the socket marked OUTPUT. The TR-08, TR-09, TR-06 and SE-02 put their audio on the same socket, so one adaptor lead covers them too.
USB. The mixer's USB port is not an option. A club mixer is a USB device and not a host, so the audio has to leave by the analogue output. Here the USB port is for a computer and for power.
CV and GATE outputs
Short answer. A mono CV OUTPUT and a mono GATE OUTPUT, both on 3.5 mm, plus a TRIGGER IN. CV carries pitch, GATE carries note on and off.
What it changes. This machine can play something that is not itself: a modular voice, an analogue synth, anything that takes a pitch voltage and a gate.
It is an output, not an input. Roland publishes CV and GATE as outputs on this machine. The SE-02 is the opposite case, with a block of CV and GATE inputs, so do not assume a Boutique's control sockets point the same way.
Output level
Short answer. Output level: N/A.
Why that matters on this machine. A mini jack arriving at a line input is where people reach for channel gain and find noise instead of level. With a bass line the temptation to push is stronger, because the part lives at the bottom of the mix.
Set it at soundcheck. Watch the mixer meters on a channel you can see.
Sync and clock
Short answer. MIDI IN and MIDI OUT, plus a TRIGGER IN jack for a pulse from other gear.
Clock over USB. From firmware 1.06 the MIDI clock source can also be USB, with soft thru switchable. Below that the option does not exist. It is the one thing on this machine worth checking before a gig.
It can lead as well as follow. The CV and GATE outputs make the TB-03 a source of timing for other gear, as well as a follower of a DAW over USB.
Power and batteries
Short answer. Four AA cells, Ni-MH or alkaline, or USB bus power at 500 mA, with about five hours on rechargeables and the usual caveat that it depends on the cells.
Batteries. When the cells run out it stops without warning, and a bass line dropping out is heard by everyone.
Do not assume the format carries. Like most of the Boutiques it takes four AA cells, and the SE-02 does not run on batteries at all.
What to watch for
Firmware: no defects, 1.06 minimum
Short answer. The TB-03 has three releases, and none is a fix to chase.
1.06, January 2019. The USB clock source and switchable soft thru described under Sync and clock. This is the floor, and it is a capability floor rather than a defect one.
1.04, November 2016. Preset patterns, a pattern copy function and a random pattern generator. Those patterns do not appear until a factory reset is performed after updating, which reads exactly like an update that failed.
1.07, November 2021. A version-number change with specifications unaffected.
Professional tips
Before the gig
Tape the audio lead at both ends. Do the CV and GATE leads too.
Updating needs a real Micro-B data cable. Roland state it in their own instructions: a dedicated charging cable will not do it. It is the most common reason an update refuses to start.
Do the factory reset after updating. The reason is under Firmware: no defects, 1.06 minimum.
Firmware, drivers and manuals
Official downloads and documents
Go to Roland for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
The Micro-B USB port carries audio and MIDI to a computer and needs Roland's own driver, which is a separate download from the system program.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Nothing comes out when I plug the TB-03 into the mixer. Why?
- Check which socket the cable is in. Only OUTPUT carries audio.
- What cable do I need?
- 3.5 mm to RCA or quarter-inch.
- Can I plug it into the mixer's USB port?
- No. Only the analogue OUTPUT sends audio to a mixer.
- Which firmware should it be on?
- 1.06 or later, if you want a clock over USB.
- Does the TB-03 have known bugs?
- No. It has a version floor instead.
- Does it have CV and GATE?
- Yes. They are outputs, so the TB-03 plays other gear rather than being played.
- Does it run on batteries?
- Yes, on four AA cells or USB at 500 mA. Expect about five hours from rechargeables.
- Why did the preset patterns not appear after I updated?
- Roland's instruction for 1.04 is a factory reset after the update.
- Is it a synthesizer?
- Roland calls it a Bass Line, not a synthesizer. This hub files it under synthesizers because that is where a reader looks for it.
- What output level does it run at?
- N/A. Treat it as unknown until the meters show it.
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's own TB-03 product and specification pages, the owner's manual and the published update history to version 1.07, checked 16 October 2026. Specifications theirs, priorities ours.