Released 2017 Reviewed: 16 October 2026

SE-02, field manual

Roland SE-02 Boutique analogue synthesizer, top view

Booth briefing. The SE-02 is an analogue synthesizer and the debut product of Roland's Boutique Designer Series, the Boutique models Roland makes with outside designers, in this case Studio Electronics. Roland describes a monophonic engine with three voltage-controlled oscillators and six waveforms, a 24 dB low-pass filter, cross modulation, a feedback loop, a tempo-syncing digital delay and a 16-step pattern sequencer with song mode. Two or more SE-02s can be chained over MIDI to make a polyphonic instrument.

Fast Lane

SE-02: equipment profile

A monophonic analogue synth with three oscillators, designed with Studio Electronics.

What comes out
One stereo OUTPUT on 3.5 mm, PHONES the same size, and an EXT INPUT jack for audio in.
Output level
N/A.
Staying in time
MIDI IN and MIDI OUT, plus VCF CV INPUT, CV INPUT, GATE INPUT, TRIGGER IN and TRIGGER OUT on mini jacks.
Computer and driver
Micro-B USB for audio and MIDI to a computer, with Roland’s driver.
Power
AC adaptor PSB-1U, 2 A. No batteries and no USB bus power. 0.95 kg without the adaptor.
Dimensions and weight
30 cm wide, 12.8 deep, 4.6 tall (11.8 × 5 × 1.8 in). 0.95 kg / 2.1 lb.
Released
2017

Specifications and update history as Roland publishes them.

SE-02: five things to know

The SE-02 in five points, each linked to its section.

It runs on the adaptor, not on batteries.

Without a mains socket it does not switch on.

Power and weight

Audio is one 3.5 mm socket, so bring the cable.

The mixer will not have a socket that fits it.

Audio output and cable

Its control-voltage sockets are inputs.

Do not assume a Boutique’s control block works the same way on every model.

Sync: MIDI, CV and gate

Below firmware 1.05 the pitch could waver.

Check the version before you blame the patch.

Firmware fixes

The last release is 1.11.

Getting to 1.11 ends the update chase.

Firmware fixes

Official equipment video

Note: This feature requires an internet connection.

Connections and setup

Audio output and cable

Short answer. The SE-02 has one stereo OUTPUT jack on 3.5 mm, with PHONES the same size. An EXT INPUT jack takes audio in.

The cable you need. Club mixers take quarter-inch or RCA, so bring your own: 3.5 mm to dual quarter-inch, or 3.5 mm to RCA. The TR-08, TR-09, TR-06 and TB-03 put their audio on the same socket, so one adaptor covers every Boutique you own.

Other 3.5 mm sockets. Several sockets on this panel are the same size and are not audio: the control-voltage inputs and the trigger jacks. Only the socket marked OUTPUT carries sound.

Output level

Short answer. Output level: N/A.

Why it matters. A mini jack arriving at a line input is where people reach for channel gain and find noise instead of level. On an analogue synth the level also moves with the patch, so there is no one setting that holds for the whole set.

Set it at soundcheck. Use the loudest patch you plan to use and watch the mixer meters.

Sync: MIDI, CV and gate

Short answer. The SE-02 has MIDI IN and MIDI OUT, plus a control-voltage block: VCF CV INPUT, CV INPUT, GATE INPUT, TRIGGER IN and TRIGGER OUT, all on mini jacks.

Direction. Most of that block is inputs, so this machine is played by something else: a sequencer or a modular rig. The single TRIGGER OUT is the only control signal it sends. The TB-03 publishes CV and GATE as outputs and this one as inputs: two Boutique machines, opposite jobs.

Pairing with a TB-03. The TB-03's CV and GATE outputs feed this machine's inputs directly, which gives you an analogue voice sequenced by something you can hold in one hand.

Power and weight

Short answer. The SE-02 runs on an AC adaptor, the PSB-1U, drawing 2 A. No batteries and no USB bus power, so a power bank will not run it.

Why it matters. Most of the Boutiques run on four AA cells or off a USB port, and anyone who learned the format on one of those will pack this one the same way. It arrives as a synth that cannot be switched on, and there is nothing in the bag that fixes it.

At the gig. You need a socket within reach of the adaptor's lead, and the adaptor itself has to be in the bag. The published weight of 0.95 kg excludes it, so budget for more than that.

What to watch for

Firmware fixes

Short answer. Roland document three fixes for the SE-02. The one that matters is 1.05, because it does not sound like a fault.

1.05, September 2017. The pitch could waver when the OSC3 level was raised. On an analogue synth that can pass for character, so an owner may never suspect a fault.

1.11, June 2018. How parameters played back when switching patterns, and the SONG tempo setting. The same release corrected the appearance of the PATCH SETUP display, which is cosmetic rather than performance.

1.11 is the last release. Roland has published nothing for this machine after it. The 1.10 release of May 2018 was a large feature addition, including Bank D and real-time pattern recording, and is not a fix.

Professional tips

Before the gig

Check the adaptor before you leave. The machine cannot run without it, as described under Power and weight.

If you own a TB-03, carry the CV lead. See Sync: MIDI, CV and gate for why the pair works.

Updating needs a real Micro-B data cable. Roland state it in their own instructions: a dedicated charging cable will not do it. With nothing newer published you may only ever do this once.

Firmware, drivers and manuals

Official downloads and documents

Go to Roland for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.

The Micro-B USB port carries audio and MIDI to a computer and needs Roland's own driver, which is a separate download from the system program.

Frequently asked questions

Quick answers

Does the SE-02 run on batteries?
No, mains only, through the PSB-1U adaptor.
Can I run it from a USB power bank?
No. It takes power from the adaptor alone.
What cable do I need to plug it into a mixer?
3.5 mm to dual quarter-inch, or 3.5 mm to RCA, from the socket marked OUTPUT.
Does it have CV and GATE?
Yes, mostly as inputs, plus one TRIGGER OUT. The TB-03 has CV and GATE the other way round.
Which firmware should it be on?
1.11, the last one Roland have published for it.
My SE-02's pitch drifts. Is that normal?
Check the version first. The only pitch fault Roland document was fixed in 1.05.
Why is the published weight 0.95 kg?
The adaptor is not counted in it.
Can I plug it into the mixer's USB port?
No. A club mixer is a USB device, not a host, so the audio has to leave by the analogue output.
Is it the same as the other Boutiques?
Same chassis and audio socket. Power and control sockets are where it differs.
What output level does it run at?
N/A, so the meters are the only guide.

Related synthesizers

Commonly paired with

What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.

Roland All brands Knowledge base FAQ and Fixes Dictionary

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Roland's own SE-02 specification page, the owner's manual and the published update history to version 1.11, checked 16 October 2026. Specifications theirs, priorities ours.