Booth briefing. The MX-1 is what Roland calls a Mix Performer, an 18-channel performance mixer with step-sequenced effects, scene memories, and transport and tempo control. Part of the AIRA series, it is built to sit with the other AIRA machines such as the TR-8, TB-3 and SYSTEM-1, which connect to its four USB host ports with audio, MIDI and sync on one cable. It also works as a USB audio interface and has a mode for Ableton Live. Roland calls it a mixer you can play, and it has a DJ-style cue function.
When it goes wrong: No sound from the mixer
Fast Lane
MX-1: equipment profile
Roland's 18-channel Mix Performer from the AIRA series, with four USB host ports for other machines.
- What comes out
- MIX OUT: quarter-inch, unbalanced. Inputs: quarter-inch pairs and a mini jack. AUX loop on RCA. Coaxial digital.
- Output level
- MIX OUT +4 dBu. Inputs variable from -26 to +4 dBu. Head room 18 dB.
- Staying in time
- MIDI IN and MIDI OUT on five-pin DIN, plus MIDI over the USB FUNCTION port.
- Computer and driver
- USB FUNCTION on type B, Roland driver required. Four USB HOST ports, type A.
- Power
- AC adaptor, 1.7 A. 1.81 kg, 400 mm wide.
- Dimensions and weight
- 40 cm wide, 26.4 deep, 6.5 tall (15.7 × 10.4 × 2.6 in). 1.81 kg / 4 lb.
- Released
- 2015
Roland's own MX-1 specification page, the owner's manual and the update history to ver. 1.05.
MX-1: five things to know
The MX-1 in five points, each linked to its section.
The USB HOST list grew past the specification page.
Which machines it accepts depends on its firmware.
Every level is published, input and output.
Few Roland machines publish any level.
The +4 dBu output is unbalanced.
Cable length matters more than usual.
A factory reset changes which clock it follows.
Nothing on the panel warns you.
Three named faults, all fixed.
The DIGITAL IN mono fault is the one a room hears.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
Inputs, outputs and levels
Short answer. The MX-1 has MIX OUT (L/MONO, R) on quarter-inch jacks, unbalanced, PHONES on a stereo quarter-inch jack, INPUT 1 to 4 as quarter-inch stereo pairs, INPUT 5/6 on a stereo mini jack, AUX SEND and AUX RETURN on RCA, and a COAXIAL IN/OUT for digital.
Published levels. Roland publish the levels, and that is worth using. MIX OUT runs at +4 dBu. The inputs are variable from -26 to +4 dBu, which covers a line source and a weak one without a separate preamp. Head room is 18 dB. Set the channel from those numbers at soundcheck.
+4 dBu, unbalanced. A high nominal level with no noise rejection is fine on a two-metre run to a mixer beside you and poor on a twenty-metre run to a stage box. Keep it short, or put a DI between the mixer and the wall.
The send and return loop is RCA. AUX SEND and AUX RETURN both, so an outboard effect goes in and comes back on phono leads rather than the quarter-inch the rest of the machine uses. Two different cable types in one box.
COAXIAL IN/OUT is the digital path. The fault Roland fixed at firmware 1.03 lived here; see What Roland has fixed.
Clock and MIDI
Short answer. The MX-1 has MIDI IN and MIDI OUT on five-pin DIN, plus MIDI over the USB FUNCTION port, and a transport and tempo section.
After a factory reset. At firmware 1.03 Roland changed the MIDI Clock Master default after a reset from Auto to Int. A machine that has been reset runs on its own internal clock and stops following the rig. It presents as everything drifting apart for no reason.
The step-sequenced effects run off that clock. So the clock setting is not a background preference on this machine, it is what decides whether the effects land with the music.
Lead or follow. It can lead a hardware rig or follow one, on ordinary five-pin leads.
Computer and host ports
Short answer. One USB FUNCTION port on type B for the computer, needing Roland's own driver, and four USB HOST ports on type A for other machines, whose accepted list depends on the firmware version.
Roland's two documents disagree about the host ports. The specification page says they are "for only TB-3/VT-3/TR-8/SYSTEM-1", four machines. The firmware history says something else: 1.03 added the JD-XA, JD-Xi, JUNO-Gi, JUPITER-50, JUPITER-80, FA-06 and FA-08; 1.04 added the JUNO-DS and the XPS-30; 1.05 added the SYSTEM-8. That is fourteen machines against four.
Read the version before you plan the rig. A machine on an early firmware genuinely does only take the four. A machine on 1.05 takes all of them. The specification page cannot tell you which you have, and neither can the panel: hold GAIN while switching on and the version appears in the CHANNEL SETTING display as three digits.
One lead instead of three. A TR-8 or a TB-3 arrives as a channel in the mixer and as MIDI.
The computer side is ordinary. USB type B carrying audio and MIDI, with Roland's driver published to 1.0.6 for macOS Sonoma 14 or later and 1.0.2 for Windows 10 and 11.
Power, size and status
Short answer. The MX-1 runs on an AC adaptor drawing 1.7 A, and nothing else. No batteries and no bus power.
It also feeds other machines. USB HOST 3 supplies bus power, so one of the units sitting on it can run off the mixer. That is one less adaptor in the bag and one more thing depending on this one.
Size and weight. 1.81 kg across 400 mm, 264 mm deep and 65 mm tall. It is a table object rather than a bag object, and the brick travels with it because there is no second route.
It is discontinued. Roland still host the manual, the system program and nine drivers, so a second-hand unit is fully supported on paper. What it will not get is another firmware release, which makes 1.05 the permanent answer rather than the current one.
What to watch for
What Roland has fixed
Short answer. The MX-1 has three named faults across four releases, and the useful line in its history is not a fault at all but a disagreement between Roland's own documents.
1.03: input through the DIGITAL IN connector became monaural. This is the one that bites in a room. A stereo source arriving through the coaxial input collapses to mono with every cable correct and nothing to see, which reads as a bad source rather than a mixer fault.
1.05, September 2016: Scene information was not restored correctly when restoring parameters. A saved setup coming back wrong is a preparation problem rather than a performance one, but it costs the same amount of time.
1.02: a factory reset might fail to complete. 1.02 also corrected the MASTER LEVEL and PAN curves, improved stability on a Mac, and improved effect accuracy at each sampling rate.
Added machines and modes. 1.03 opened the USB HOST ports to seven non-AIRA machines, 1.04 added two more and an Ableton mode with clip and scene playback, track solo, arm and mute and AUX send, and 1.05 added the SYSTEM-8.
Clock default. Not a fault: 1.03 changed a default, described under Clock and MIDI.
Professional tips
Before the gig
Check which firmware is installed before you promise anyone a USB HOST connection. Below 1.05 the list is shorter, and which machines are missing depends on how far below.
Check the clock source after any factory reset. The reason is under Clock and MIDI.
Put a DI at the mixer end. It costs very little and removes the question of cable length.
Pack RCA leads for the send and return. It is the cable somebody forgets.
Firmware, drivers and manuals
Official downloads and documents
Go to Roland for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
The version of record is 1.05. Roland publish the owner's manual in seven languages plus, in English, a Supplementary Manual, guides to the Ableton Live and EXTERNAL MIXING modes, a MIDI Implementation document and an audio signal-flow diagram. The signal-flow diagram is the one worth having on a machine with this many routes through it.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Which machines can I connect to the MX-1's USB HOST ports?
- It depends on the firmware: four machines originally, fourteen by 1.05.
- How do I check the firmware version?
- Switch it on while holding GAIN. The display shows three digits, so 1.00 reads 100.
- What output level does it run at?
- +4 dBu at MIX OUT, with 18 dB of head room.
- Is the output balanced?
- No, MIX OUT is unbalanced, so use a DI on a long run.
- Why is my digital input coming through in mono?
- It was a fault fixed at 1.03, so check the firmware version.
- My mixer stopped following the external clock. Why?
- Check for a factory reset. It leaves the clock on Int.
- Does it run on batteries?
- No. Only the AC adaptor, though it can power a machine on USB HOST 3.
- What cables does the send and return need?
- RCA, not quarter-inch.
- Does it need a driver?
- Yes, but only for the computer connection.
- Is it still made?
- No. It is discontinued, and 1.05 is the last firmware.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's product pages and owner's manual for the MX-1, and its published update history, checked 17 October 2026. Specifications theirs, priorities ours.