Booth briefing. The Traktor MX2 is Native Instruments' two-channel all-in-one controller for Traktor, described on their product page as a "Creative 2-channel DJ controller" and pitched at DJs starting out, from a session at home to a packed club. It is one of three units in NI's DJ controller collection, beside the X1 and the Z1. A club-standard mixer layout, two jog wheels without motors, 16 RGB pads and an audio interface sit in one unit. It needs a computer running Traktor Pro 4 to make any sound, and the full version of Traktor Pro 4 comes with it.
Fast Lane
Traktor MX2: equipment profile
Native Instruments' two-channel Traktor controller, built around a mixer and a pair of jog wheels.
- Without a computer
- Nothing. USB to a computer running Traktor Pro 4 is required.
- Software
- The full version of Traktor Pro 4, plus two months of Beatport streaming. Traktor Pro 3 is not supported.
- Ports
- A balanced 1/4" TRS microphone input, USB-C, and an external power connector.
- What the computer needs
- macOS 13, 14 or 15, or Windows 11, on an Intel Core i5 or Apple M1, M2 or M3, with 4 GB of RAM.
- Released
- No launch date published
The five things that decide your gig
The Traktor MX2 in five points, each linked to its section.
It needs a computer, and Native Instruments say so directly.
Native Instruments answered the exact question in their own FAQ.
Mixer FX has eight effects, or nine, depending which Native Instruments page you read.
Treat the number as unconfirmed until Native Instruments settle it.
The jog wheels are not motorised.
Turntable and Jog modes change how the wheel behaves.
Sixteen pads in four modes.
A dark pad row is usually a setting, not a fault.
MIC VOL is the one control not to touch mid-set.
Set it at soundcheck, not during the set.
Official equipment video
Note: This feature requires an internet connection.
Features explained
A club-standard two channel mixer, built around a computer
What it is. A 2-channel all-in-one DJ controller: a club-standard mixer, two jog wheels and 16 pads, with a built-in audio interface, in one unit. It needs a computer running Traktor Pro 4 to do anything; see standalone below.
What Native Instruments call it. Native Instruments title the product "Traktor MX2" and describe it on the product page as a "Creative 2-channel DJ controller." The page pitches it at a DJ starting out, under the line "Start out to stand out," and names use cases from a solo session at home to a packed club.
Short answer. 2 channel faders, 2 VU meters, a crossfader, 3-band EQ per channel and 2 pitch faders, which Native Instruments call a club-standard layout.
Gain and EQ. The manual describes GAIN as the level into the channel strip before anything else touches it, and the three EQ knobs, HI, MID and LOW, as centred and neutral: "Pulling the knob to the right emphasizes its frequency band, while pulling it to the left attenuates" it, down to a full kill at the left end.
The audio interface underneath it. A 24-bit audio interface built around a Cirrus Logic DAC, running at 44.1, 48, 88.1 or 96 kHz, with iZotope's Ozone Maximizer built into the output path per the product page.
The jog wheels: Turntable mode against Jog mode
What the manual says. Touch-sensitive jog wheels with two modes, Turntable and Jog. In Turntable mode, stopped, turning the outer ring or the top plate moves the playhead, and holding SHIFT while turning the top plate fast-seeks; playing, the outer ring bends tempo temporarily and the top plate holds playback while moving the playhead. In Jog mode the top plate behaves like the outer ring, so both surfaces bend tempo while playing and move the playhead while stopped. Native Instruments' FAQ states plainly that they are not motorised: "No, they are the same size as Traktor S4's jog wheels, but they are not motorised."
Mode, not fault. A wheel that bends tempo instead of holding playback, or the reverse, is usually the mode. Both modes look like broken hardware if you do not know they exist.
Every pad mode, one by one
The full list. Sixteen RGB pads across four modes. HOTCUE: an unlit pad stores a cue point, or the current loop if one is active, and a lit pad jumps to it; SHIFT plus a lit pad erases it. STEM: the upper row mutes and unmutes individual stems of a loaded Stem track, the lower row selects one, and the Move and Loop encoders adjust its volume and filter amount. PATTERN: only available when a Deck's FX Unit is set to Pattern Player mode, showing the first eight steps by default, with a second press switching to the last eight and SHIFT clearing the grid. FLUX: holding a pad switches the deck to Flux mode and triggers a loop of a preset size, releasing it returns the playhead to where it would have been had nothing been held. Native Instruments' own FAQ and specification page list the top-level set as Hot Cues, Stems, Loops and Pattern Player; the manual documents the loop behaviour inside Hotcue mode rather than as a fifth, separate mode.
A pad row that will not respond. Check the FX Unit mode before suspecting a fault: Pattern is the mode that depends on it.
Deck FX, the other effects section
Short answer. Each deck carries its own FX Unit, four knobs and four buttons mirroring the software, with SHIFT plus the first button cycling the unit between Group, Single and Pattern Player modes. Native Instruments give access to more than 40 effects this way, and the FX Unit is not fixed to its own deck: a channel's FX Assign button can route either deck's unit to either channel.
How it differs from Mixer FX. Mixer FX lives on the mixer channels and applies one effect to both decks at once; Deck FX lives on each deck.
MIDI mode, for software other than Traktor
Short answer. Pressing both SHIFT buttons together switches the unit in and out of MIDI mode for third-party software, which the FAQ page documents; the LEDs turn blue while it is active. The user guide PDF does not cover this mode at all, so only the FAQ documents it.
Telling it from a lost connection. A unit that controls nothing in Traktor, with blue LEDs, has been switched into this mode.
The factory mapping can be adjusted, within limits. Native Instruments state that some parts of the factory mapping can be changed from a dedicated MX2 Preference Page inside Traktor, without naming which parts.
Connections and setup
Every socket on it
Outputs and inputs. Master out on RCA and on a 1/8" mini jack; headphone out on 1/8" and 1/4" TRS; a balanced 1/4" TRS microphone input; USB-C; an external power connector.
Headphone cueing. Each channel has a Cue button that sends it to the headphone mix. The MIX knob reads by its ends: full left is cue channel only, full right is the main signal only, matching the wording Native Instruments use elsewhere in the Traktor line. A separate VOL knob sets headphone level.
Measured performance, as Native Instruments publish it. Native Instruments publish measured figures at 48 kHz. Master out (RCA): +12 dBu, 0.001% THD+N across 20 Hz to 20 kHz, 109 dB dynamic range A-weighted, 150 ohm output impedance. Headphone out: +12.3 dBu, 0.002% THD+N, 100 dB dynamic range, 2 x 110 mW into 33 ohms. Mic input: -10 to -57 dBu depending on gain, 0.0024% to 0.0387% THD+N, 99 to 71 dB dynamic range depending on gain, 14 kilohm balanced input impedance, with an adjustable gain range of 47 dB.
Size and weight. 511.4 x 61.9 x 323.1 mm (W x H x D), 2730 g. Native Instruments' own FAQ compares this against the Traktor S2 MK3 at 486 x 59 x 265 mm, to give a sense of scale against an older, smaller all-in-one controller.
The microphone input
Short answer. A rear-panel ¼" microphone input with its own MIC VOL knob and a MIC button on the mixer that mutes and unmutes it in the main mix. Native Instruments' own instruction is to start with MIC VOL fully left, connect the microphone, then raise the knob gradually, and their one explicit caution in the guide is against touching it mid-set: feedback "could damage the ears of your audience, and yours."
No limiter. There is no separate limiter for this input beyond the knob itself.
Compatibility
Software, drivers and what the computer has to be
The licence comes with the box. Native Instruments bundle what they call the full version of Traktor Pro 4, plus a two-month Beatport streaming subscription. Traktor Pro 3 is not supported: the FAQ states plainly, "No, a full version of Traktor Pro 4 is required but comes included free."
The computer. macOS 13, 14 or 15, or Windows 11, on an Intel Core i5 or Apple M1, M2 or M3, with 4 GB of RAM. An internet connection and OpenGL 2.1 graphics are required to download and activate the software; the product runs offline after that.
What to watch for
It does not run without a computer, and Native Instruments say so directly
Short answer. The Traktor MX2 is not standalone. Nothing without a computer. Native Instruments' FAQ is direct: "No, the MX2 must connect via USB to a computer running Traktor Pro 4." Once Traktor is installed and activated, the system requirements note the software itself can run offline, which is a different claim from the hardware working alone.
Plan around it. Nothing sits behind the hardware as a fallback, so the laptop is the one part of the rig that cannot fail.
Mixer FX: eight effects, or nine, by Native Instruments' own count
How it works on the Traktor MX2. One knob per channel doing two jobs at once when that channel's FX button is on: "this knob simultaneously filters the channel and controls the amount of Mixer FX applied to the remaining part," centred for no effect, turned left for a highpass filter with the effect on the lows and mids, turned right for the reverse. Five buttons, four numbered plus FILTER, choose which effect is active for both channels at once; holding one down while pressing a channel's FX button applies that effect to that one channel only.
The disagreement. Native Instruments' own FAQ page states Mixer FX offers "eight available effects, including Delay, Reverb, and Gater." Both the Creative tools section of the product page and the specifications page say nine. Nothing published names the ninth effect or says which total is current.
Professional tips
Before you travel
The power supply travels with the controller, always. Native Instruments state it carries no battery mode and no documented USB-only operation, so leaving the brick at home ends the set before it starts.
It pairs with other Traktor gear. Native Instruments document using the MX2 alongside other Traktor hardware, naming the Traktor F1 as an example for controlling clips in a Remix Deck.
Watch the clipping LED, not your ears. A clipping LED sits on the MAIN output. If it lights, the documented fix is to turn the MAIN knob left until it goes out; the guide carries no other troubleshooting section.
Safety
What the manual tells you to do, and in what order
The Traktor MX2 has a published switch-on order. Native Instruments publish a five-step switch-on order: MAIN and headphone VOL knobs fully left, then the computer, then the MX2, then the amplification system, then start Traktor.
Hearing. The guide's one explicit caution is about the microphone input, described under The microphone input.
Firmware, drivers and manuals
Official downloads and documents
Go to Native Instruments for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
Firmware. Native Instruments publish no firmware version and no change history for the MX2, so there is no number to check yours against. The firmware exists. The record of it does not.
Faults. No recall and no Native Instruments service notice was found for this controller.
Release date. Native Instruments never dated the MX2’s launch. The product page carries only a copyright notice, and the press area names no launch date.
Manuals. Official Native Instruments manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Does the Traktor MX2 work without a computer?
- No. There is no standalone mode.
- Are the jog wheels motorised?
- No. They sense touch but do not move on their own.
- How many effects does Mixer FX have?
- Two totals are published; see the Mixer FX section.
- Does it work with Traktor Pro 3?
- No, only Traktor Pro 4 is supported.
- What year was the Traktor MX2 released?
- No launch date has been published.
Related all-in-ones
Native Instruments All brands Knowledge base FAQ and Fixes Dictionary
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: the maker's own product page, specification table, FAQ page and user guide PDF, checked 22 October 2026. Specifications theirs, priorities ours.