Released 2018 Reviewed: 17 October 2026

VT-4, field manual

Roland VT-4 voice transformer, top view

Booth briefing. The VT-4 is the voice transformer in Roland's AIRA series, the successor to the AIRA VT-3: an effect processor for the human voice, with dedicated faders for pitch and formant. It does harmony, vocoding, pitch shifting, hard tuning and robot voices, alongside delay and reverb, and a MIDI keyboard can guide the pitch, harmony and vocoder effects. Roland names singers, DJs, electronic musicians and web broadcasters as its users. For a DJ it is a voice effect that sits between a microphone and the mixer.

Fast Lane

VT-4: equipment profile

Roland's voice transformer from the AIRA series, the successor to the VT-3, built for one job: a voice in and a changed voice out.

What comes out
LINE OUT: quarter-inch, R/BYPASS. PHONES: mini jack. Rear MIC IN: combo XLR/TRS, +48 V. Front: mini jack.
Output level
N/A. Converter: 24 bits, AD and DA at 44.1, 48, 96 and 192 kHz.
Staying in time
MIDI IN only. No MIDI OUT.
Computer and driver
USB type B, Roland driver required.
Power
Four AA cells or USB bus power (500 mA). 554 g with batteries.
Dimensions and weight
17.4 cm wide, 13.3 deep, 5.8 tall (6.9 × 5.2 × 2.3 in). 0.55 kg / 1.2 lb.
Released
2018

Roland's own VT-4 specification page, the owner's manual and the update history to ver. 1.03.

VT-4: five things to know

The VT-4 in five points, each linked to its section.

Two mic inputs, and only the rear XLR one carries phantom power.

A condenser plugs straight in at the back.

Inputs and outputs

MIDI IN, and no MIDI OUT.

It always sits downstream of the rig.

Clock and MIDI

Phantom power costs battery life.

A long set starts with the choice of microphone.

Power and weight

The update will not run on batteries.

Bring the cable and a computer.

What the computer needs

A single fault is named, and it needs a MIDI source to show.

It matters only if a sequencer sends it tempo.

What Roland has fixed

Official equipment video

Note: This feature requires an internet connection.

Connections and setup

Inputs and outputs

Short answer. The VT-4 has two microphone inputs, LINE OUT (L/MONO, R/BYPASS) on quarter-inch jacks, PHONES on a stereo mini jack, and a USB type B port.

The rear microphone input is a combo XLR and quarter-inch TRS, balanced, with +48 V phantom power at 10 mA maximum. A condenser works on it directly, with no interface and no separate preamp in front.

The front input is a stereo mini jack with plug-in power. It is for a headset microphone, so a performer can wear the mic and keep both hands on something else.

R/BYPASS. The right output jack doubles as a bypass feed, so the dry voice can go to its own channel at the mixer while the processed voice goes to the other. The engineer can then pull the effect out of the room without touching the VT-4.

Output level. N/A. The converter is 24 bits, with AD and DA conversion at 44.1, 48, 96 and 192 kHz.

Clock and MIDI

Short answer. The VT-4 has a MIDI IN jack and no other MIDI connector.

Receive only. A keyboard or a sequencer sends it notes and the robot voice follows them to pitch. The VT-4 sends nothing back, cannot be the clock, and cannot pass on what it receives.

An interrupted MIDI stream used to leave the voice stuck. Firmware 1.02 added a setting that turns the robot voice OFF when MIDI note input stops, which is the fix for a note that hangs when a cable is pulled or a sequencer stops, and which on stage sounds like a machine that has crashed. On a unit below 1.02 that setting does not exist.

USB carries MIDI as well as audio. If the rig is already computer-centred, one type B cable does both and the DIN socket stays empty.

What the computer needs

Short answer. The VT-4 has a USB type B port and needs Roland's own driver, published to 1.0.3 for macOS Sonoma 14 or later and 1.0.1 for Windows 10 and 11.

The update cannot be run on batteries. Roland's system program page says it twice: the update is carried out using USB power, and the VT-4 cannot be updated using battery power.

Checking the version is a button sequence, not a screen. Power off, connect USB, hold MEGAPHONE and switch on; the BYPASS button flashes, press it twice, and a dark Scene Memory 3 button means the update applies. An illuminated one means the unit is current.

Roland keep a support article for a Windows 10 driver that does not install itself. If the computer sees nothing after plugging in, check the driver before the cable.

Power and weight

Short answer. The VT-4 runs on four AA cells, Ni-MH or alkaline, or on USB bus power at 500 mA. There is no DC input on the connector list.

Battery life. Phantom power shortens the running time, and Roland publishes all four numbers. Alkalines give about 6 hours with phantom off and about 4 with it on. Ni-MH cells give about 7 hours off and about 5.5 on.

A dynamic microphone runs longer. If the set is long and the room is loud, a dynamic mic on the combo jack with phantom switched off is the longer-running choice.

Weight and size. 554 g including the batteries, 174 mm wide and 133 mm deep. Roland's weight figures usually exclude what powers the machine; this one includes it.

What to watch for

What Roland has fixed

Short answer. Roland's update history for the VT-4 names one fault, at 1.03, and it only appears when something else is driving the unit.

1.03, November 2021. With a realtime message arriving at the MIDI IN connector, specific REVERB types failed to synchronise with the tempo information. A tempo-locked reverb drifting against the track looks like a sequencer problem, not a VT-4 problem.

1.02, November 2018. It added settings for constant pitch and formant conversion, a mute feature, and the robot-voice-off setting described under Clock and MIDI.

Nothing has been published since November 2021. A unit on 1.03 carries everything Roland has issued.

Professional tips

Before the gig

Update it at home, on the cable. The venue is the wrong place to discover you are two versions behind.

Ask the engineer for two channels and explain BYPASS. The reasoning is under Inputs and outputs.

Pick the microphone before you pick the batteries. The running times are under Power and weight.

Set the robot-voice-off behaviour before you need it. It needs firmware 1.02 or later.

Firmware, drivers and manuals

Official downloads and documents

Manuals, drivers and the system program are on Roland's site. The links below go to Roland's own pages, which stay up to date.

The VT-4 version of record is 1.03. Roland publish the owner's manual in eight languages, plus a Block Diagram and a MIDI Implementation document in English, and six drivers.

Frequently asked questions

Quick answers

Can I use a condenser microphone with a VT-4?
Yes, on the rear XLR input.
What is the small input on the front for?
A headset microphone, which gets plug-in power rather than phantom.
Why will the update not start?
Usually because the unit is on batteries.
How long does it run on batteries?
Roughly 4 to 7 hours, depending on the cells and on phantom power.
Can it send MIDI to my other gear?
No. It only receives.
What does R/BYPASS mean on the output?
The right LINE OUT jack can carry the dry voice.
My robot voice sticks on a note. Why?
Probably the MIDI note stream stopped. The fix is a setting from firmware 1.02.
Which firmware should it be on?
1.03. Roland has published nothing after it.
Does it need a driver?
Yes, Roland's own, and Windows 10 may not install it by itself.
What does the published weight include?
It includes the batteries.

Related vocal processors

Commonly paired with

What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.

Roland All brands Knowledge base FAQ and Fixes Dictionary

Playing soon and it is not working?

Start Emergency Mode

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it

Sources: Roland's product pages and owner's manual for the VT-4, and its published update history, checked 17 October 2026. Specifications theirs, priorities ours.