Booth briefing. The RANE SEVENTY-TWO is a professional two-channel battle mixer for Serato DJ Pro, the original touchscreen model of RANE's SEVENTY family, with a 4.3-inch touchscreen between the channels for waveforms, effects and library browsing. Its faders are MAG THREE, where the SEVENTY-TWO MKII that followed it has MAG FOUR. Each channel can take a computer deck, a phono or CD source or Aux, and the analogue positions play without a computer. For a scratch DJ it is the mixer that put a screen in the middle of a battle setup.
When it goes wrong: No sound from the mixer
Fast Lane
SEVENTY-TWO: equipment profile
A two channel Serato mixer with three contactless MAG THREE faders and a 4.3 inch touchscreen.
- Ports
- Input levels: phono RIAA to plus 0.1 and minus 0.2 dB with 30 dB of gain at 1 kHz and 126 mV maximum, line and Aux 4 Vrms, mic 0.126 Vrms on Mic and 2.3 Vrms on Line with gain trim from off to plus 20 dB.
- Sound out
- Main and booth: 20 Hz to 20 kHz within plus or minus 0.2 dB at 0.002% THD+N.
- Output level
- Main and booth: 8 Vrms. Session Out: 4 Vrms. Headphones: 96 mW into 50 ohms.
- What the computer needs
- Serato DJ Pro. Two Type-B ports, one per computer. Windows driver: inside the Rane Control Panel.
- Power
- IEC inlet, 100 to 240 V at 50/60 Hz, 30 W.
- Released
- 2018
The five things that decide your gig
The RANE SEVENTY-TWO in five points, each linked to its section.
MAG THREE faders, not the MKII's MAG FOUR.
Check the fader class before ordering any part.
Fader tension is a screwdriver job with the faceplate off.
Do it at home, before the gig.
A deck on PH/CD or Aux stops sending MIDI.
The pads go quiet and nothing says why.
Never put a USB drive in the Twelve and Controller ports.
The damage looks unrelated to the port, because the Deck Source knob triggers it.
Firmware version: N/A.
Do not borrow the MKII's version number.
Features explained
Three MAG THREE faders, and the tension screw
RANE fit three contactless MAG THREE faders with adjustable tension, two channel faders and one crossfader. The MKII fits MAG FOUR, so a replacement fader, a calibration note or a tension instruction written for one model is not advice about the other.
The tension is adjustable but not from outside. RANE's procedure is to make sure the unit is powered off and disconnected from a power source, remove the fader caps, unscrew the faceplate at the bottom of the top panel where the faders are, and turn the tension screw on each MAG THREE fader with a screwdriver. That is a workbench job with the mixer out of the rig, not a thirty second adjustment between tracks.
The Contour control adjusts the slope of the crossfader curve: turn it left for a smooth fade for mixing, right for a sharp cut for scratching, and RANE name the centre position as a typical setting for club performances.
The front panel carries the headphone outputs on quarter inch and eighth inch, Mic 2 On, Mic 2 Level, Mic 2 Tone, Mic 1 Echo, the Contour control for the crossfader curve, a Fader Reverse switch per fader, a Deck Swap switch and the footswitch input. RANE list no crossfader tension knob on this model, which is why the tension procedure above needs a screwdriver.
The touchscreen and the pads
The touchscreen is a full-colour capacitive multi-touch display, 54 by 95 mm and 4.3 inches on the diagonal. View/Menu toggles Waveform and Library views and Effects/Tap opens Effects View. In Waveform view the overview can be scrubbed with a finger, and pinching two fingers zooms the large waveform in and spreading them zooms out.
Sixteen velocity-sensitive multi-colour backlit pads, eight per deck, with ten modes each. RANE put Pad Sensitivity in the Main Menu under Pad Setup.
Connections and setup
The rear panel, item by item
Rear panel, in RANE's own order: the IEC power input and power switch, two XLR main outputs, two balanced quarter inch booth outputs, an RCA Session In whose signal is sent directly to the program mix, an RCA Session Out, an RCA PH/CD input per deck with its PH/CD selector and phono ground terminals, an RCA Aux input per deck, two combo XLR and quarter inch mic inputs each with a Line/Mic selector, two USB Type-A ports for a Twelve or another USB MIDI controller, and two USB Type-B ports for computers.
The rear PH/CD selector has to match the box plugged into it. RANE say to set it to PH for phono-level turntables, to provide the additional amplification needed for phono-level signals, and to CD for a line-level device such as a line-level turntable, CD player or sampler.
Two mic channels that are not equals
The two mic channels are not equals. Mic 1 has level, tone and an echo whose feedback, ducking threshold and ducking hold time are set in Main Menu under Mic 1 Setup, with the echo amount on a front panel knob and an echo button on the top panel. Mic 2 is front panel only, with on or off, level and tone.
Mic Inputs 1 and 2 are mono combo XLR and quarter inch jacks whose signals are split and routed directly to the stereo program mix and cue channel, and each has a rear Line/Mic selector that must be set to Mic for a microphone and to Line for a line-level device such as a keyboard or sampler. RANE name no phantom power for either input. For a stereo line source, RANE point at the Session In instead.
Main Menu > Audio Out carries a Mic 1 Clean Feed setting with a consequence worth knowing before a recorded set: when Clean Feed is On, Mic 1 will not pass audio when recording in Serato DJ Pro.
Two computers, and the port you must not use
Two USB Type-B ports carry audio and MIDI to and from two computers, which is what makes a changeover possible without unplugging anything. RANE do not say whether both machines can run Serato simultaneously.
In Library View the touchscreen shows the Serato library of the connected computer, and RANE say which one it picks when there are two: if the SEVENTY-TWO is connected to two computers, the one to which both decks were last assigned will be shown.
RANE print one prohibition on the Twelve and Controller USB ports, and it is tied to the Deck Source knob: do not connect USB drives to these ports, because switching the Deck Source knob will force eject the drive from the connected computer, which could damage the contents and should be avoided.
Compatibility
Deck sources, and when a deck stops being a controller
Each channel has one Deck Source knob with four positions: USB A or USB B, meaning a track playing on that layer in the software, PH/CD, meaning a device connected to that deck's PH/CD In on the rear panel, and Aux, meaning a device connected to the Deck Aux In.
RANE state the limit in one line: a deck's controls will send MIDI information only when its deck source selector is set to USB A or B. A deck switched to PH/CD or Aux stops being a controller.
The SEVENTY-TWO makes sound with no computer attached. A channel set to PH/CD or Aux plays whatever is wired to that deck's rear input, the Session In signal is sent directly to the program mix, and both mic signals are split and routed directly to the stereo program mix and cue channel. The computer is what the USB A and USB B deck positions, the performance pads and the MIDI they send depend on.
Serato, the box contents and the driver
RANE list two Serato NoiseMap control vinyl records and two Serato NoiseMap control CDs in the SEVENTY-TWO's box contents, which is what a DVS setup needs, alongside two USB cables and the power cable.
RANE list a Serato Pitch 'n Time download card with a serial number in the box contents, and the touchscreen reflects it: with Key Lock selected, the field shows a Serato Pitch 'n Time icon in place of the Key Lock icon when the expansion is installed.
RANE ask every owner to register the mixer at dj.rane.com and download the Rane Control Panel, and they scope the driver inside it: Windows users only, the Rane Control Panel contains drivers required for Windows.
The Rane Control Panel adjusts the mixer's settings from a connected computer and saves and loads them as an .r72 file, under the General tab in the Settings section, so one configuration can travel between situations.
What to watch for
Firmware
Firmware version for the original SEVENTY-TWO: N/A. The user guide asks you to check dj.rane.com for updates, especially after updating your software. The 1.6 file listed under this model's name sits in the MKII's folder on inMusic's servers, so it belongs to the MKII. Treat the installed version as whatever the updater reports.
The settings that change how it behaves
RANE note it once on the SEVENTY-TWO, against the EQ and filter knobs: all EQ and Filter controls are full-kill. The filter cutoffs themselves are editable in Main Menu under Filter Setup, as Low Pass Min for the LOW position and High Pass Max for the HI position, alongside the deck and sampler resonance.
Cut-In Adjust in the Main Menu controls the amount of dead space between a fader's closed and open positions. You select the fader you want to adjust, move that fader to the position you want, and press Set to store the setting.
Phono 1/2 Sensitivity sits in Main Menu under Deck Settings, alongside Tone XOver and Deck Pan, and RANE's instruction for it is one line: set Phono Sensitivity to the settings recommended by your cartridge's manufacturer.
The front panel has a quarter inch footswitch input, and RANE specify what it takes: a three-switch footswitch with passive-contact closure. Main Menu then assigns each of the three to MIDI, to FX 1 or FX 2 Latch, to FX 1 or FX 2 Moment, or to Tap.
If something goes wrong
A low hum or buzz on a turntable deck
RANE join the symptom to the cause on the SEVENTY-TWO: if you experience a low hum or buzz, this could mean that your turntables are not grounded. The ground wire goes to the terminals beside the PH/CD inputs, and RANE add that some turntables have a grounding wire built into the RCA connection, in which case nothing needs to be connected to the grounding terminal.
The screen will not scrub, or the faders feel swapped
Scrubbing the waveform has a software condition RANE spell out: if the Disable Needle Search option in Serato DJ Pro has been enabled, you have to hold Shift to scrub through the track. A screen that will not scrub is usually that setting rather than a fault.
A Deck Swap switch on the front panel swaps the left and right channel faders as controlled by the SEVENTY-TWO. Off is the conventional configuration. If the channel faders feel like they belong to the other decks, that switch is the first thing to look at.
Frequently asked questions
What is it, and which document says so?
RANE describe the SEVENTY-TWO as a premium two channel Serato mixer built for the pro, club and scratch DJ, with solid steel construction. Two channels, a 4.3 inch multi-touch screen in the middle of the top panel, and three contactless magnetic faders.
User Guide, version 1.3, a 104 page multilingual document with English on pages 3 to 22 and Spanish on 23 to 42. The PDF was created on 10 September 2018 and last modified on 22 October 2018.
How big is it, and in what order does it power up?
285 x 445 x 105 mm and 5.6 kg, which is RANE's own figure, on an IEC inlet taking 100 to 240 V at 50/60 Hz and drawing 30 W. The converters are AKM at 24-bit and 48 kHz with 32-bit floating point double precision processing, and RANE quote 114 dB of A-weighted dynamic range on the converters.
RANE give the order in both directions. Starting a session, turn on input sources, then the SEVENTY-TWO, then output devices; ending a session, turn off output devices, then the SEVENTY-TWO, then input sources.
Manuals. Official RANE manual page →
Broken link? Let us know and we'll fix it.
Where this sits in the line
- Next generation SEVENTY-TWO MKII
Related mixers
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Keep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy