Booth briefing. The RANE TWELVE is a motorised control deck from RANE, supported as an official accessory in Serato DJ Pro, and the first generation of the TWELVE. It is not a turntable and makes no sound of its own: its spinning platter controls the software, so it needs a supported Serato DJ Pro interface, controller, mixer or Club Kit to do anything at all. Up to four can run together, with the mixer's channel count deciding how many. For a scratch DJ it was the motorised alternative to timecode vinyl, now followed by the TWELVE MKII.
When it goes wrong: A turntable that hums
Fast Lane
TWELVE: equipment profile
A motorised quartz direct drive control deck for Serato DJ Pro, with a 332 mm die cast aluminium platter and a 12 inch control disc.
- Ports
- USB Type-B and IEC power inlet, in a recess underneath the deck.
- Sound out
- None. No audio connectors of any kind.
- What the computer needs
- Serato DJ Pro. Up to four TWELVE controllers, limited by the channel count of the Serato device.
- Power
- IEC inlet, 100 to 240 V at 50/60 Hz, 60 W.
- Released
- 2018
The five things that decide your gig
The TWELVE in five points, each linked to its section.
It has no audio connectors at all.
Bought second-hand without a supported Serato device, it cannot be made to produce sound by any cable.
The motor torque switch is underneath the deck.
Finding it means flipping the deck.
The four spacers in the box set the spinback.
Nothing on the deck reports where it is set.
Up to four TWELVEs, if the mixer has the channels.
Two channels mean two TWELVEs.
Firmware for the TWELVE: N/A.
There is nothing to check and nothing to install.
Features explained
The platter, the torque figures and the strobe
The specification table puts numbers to that switch. High is 5.0 kgf/cm starting and instant, falling to 3.4 kgf/cm stable. Low is 3.2 kgf/cm starting and instant, falling to 1.4 kgf/cm stable. Starting time is under 0.4 seconds and braking is electronic.
The dial at the top of the strobe light turns the platter motor off while leaving the unit powered, which is what makes wind down effects possible. The strobe itself lights the edge of the platter so the speed dots can be read: still dots mean the phase of rotation is constant, drifting dots mean it is not.
RANE print one warning against the platter itself: it should not be held in position for sustained periods while powered to rotate. Holding a stall is a motor instruction, not a technique the deck is built to absorb.
The control disc, the spacers and the spindle
The control disc is a full size 12 inch, 30.5 cm disc that controls the audio playhead in the software, held to the spindle by a Quick Release Adapter. To take it off, hold the button on the side of the adapter while lifting. To lock it back on, pinch the top of the spindle and rotate the disc slowly until it clicks, which happens when the groove in the spindle lines up directly opposite that button.
Four spacers come in the box and they are the spinback adjustment. Placing one to four of them over the spindle underneath the slipmat raises the control disc, and RANE state the relationship plainly: the more the disc is elevated, the more spinback you get. It is a mechanical feel change with no menu and no setting.
The control disc is user replaceable. RANE say the Quick Release Adapter can be attached to your own modified disc, that the replacement must have three 6 mm holes, and that the included disc should be used as a reference.
The touch strip, the pitch fader and the LEDs
A pressure sensitive touch strip replaces the tone arm and sets track position. Its behaviour depends on the Touch Strip Mode button beside it, which toggles between Needle Drop and Hot Cue. Needle Drop is the default every time the TWELVE is powered on, and the button is dimly lit in that mode and brightly lit in Hot Cue.
The LED ring around Start/Stop reports three states rather than two: dim when the unit is powered and no track is playing, bright while a track plays, and flashing red when the track is near its end. That last one is a warning you can see from across a booth without looking at a screen.
Two speeds, 33 1/3 and 45 RPM, selected by their own lit buttons. The pitch fader range is switched between plus or minus 8, 16 and 50 percent by the Pitch Range buttons.
Switching decks can leave the pitch fader disagreeing with the software, and the Takeover LEDs are how that is resolved: an arrow lights in the direction the fader has to move, and it goes out when the fader matches the software and can control it again.
Connections and setup
What is underneath, and what it has no socket for
The TWELVE has no audio connectors of any kind. The whole connector list is one USB Type-B port and one IEC power inlet, both in a recess underneath the deck. It sends control data and nothing else, which is why RANE state that it requires a supported Serato DJ Pro interface, controller, mixer or compatible Serato Club Kit solution. On its own it makes no sound and cannot be made to.
The connectors are not on a rear panel. They sit in a recess in the bottom panel, and so does the motor torque switch, which is the control most likely to be hunted for: the power inlet, the power switch, the Motor Torque switch and the USB port, in that order.
One USB cable, and RANE give two destinations for it. With a SEVENTY-TWO, it goes to the Deck 1 or Deck 2 USB ports labelled Twelve/Controller on that mixer. With any other mixing interface, it goes to a USB port on the computer or to a powered hub connected to the computer.
The motor torque switch, and where it hides
Motor Torque is a two position switch underneath the deck, and RANE describe both ends in feel rather than numbers: at the high setting the platter has the heavier, stronger feel of modern turntables, and at the low setting it is lighter and more graceful, the feel of a classic turntable. A platter that feels wrong is this switch before it is anything else, and finding it means turning the deck over.
Compatibility
What it needs before it does anything
RANE say the TWELVE was designed in collaboration with Serato, which makes it an Official Serato Accessory. That is a statement about the partnership, not a licence: nothing in the box activates Serato DJ Pro, and the box contents list no licence card of any kind.
The box holds the base, the platter assembly of aluminium platter, slipmat, control disc with the Quick Release Adapter already attached and four spacers, a power cable, a USB cable, the user guide and the safety and warranty manual. There is no software licence of any kind in that list.
Four TWELVEs, if the mixer has the channels
Up to four TWELVE controllers can run with one Serato DJ Pro enabled device, but RANE attach a condition that decides it in practice: provided the device has enough channels. They give the example themselves, that a two channel mixer such as the SEVENTY-TWO supports only two TWELVE controllers, with only the first two channels available for selection.
Assigning several TWELVE controllers is a procedure rather than a setting. Power each one on and the available Deck Select buttons flash on all of them. Press the button for the deck you want that unit to take, and it lights fully while the other available decks dim. Holding a Deck Select button for two seconds releases that deck and sets the buttons flashing again, ready to be reassigned.
What to watch for
Firmware
An error in RANE’s own specification table
The TWELVE's specification table gets the platter weight wrong by a factor of a thousand. It reads 4.9 lbs. and 2.2 g, and 4.9 lbs is 2.2 KILOGRAMS. The imperial figure is the one to trust, and this is the same class of error as the spec table on the FOUR.
If something goes wrong
Fitting the platter, and the power order
The platter is fitted rather than shipped in place. RANE have you align the pins in the bottom of the platter with the holes in the motor, press it down firmly, and check that it rotates uniformly and does not wobble excessively before going any further.
RANE give the order for the power cable in both halves: with the power switched off, plug the cable into the TWELVE first and then into the wall.
Frequently asked questions
What is it, and which document says so?
RANE describe the TWELVE as a pure and powerful motorised DJ control system that keeps a familiar turntable layout and size in an all-metal body, and name the one clear difference themselves: a precision multi-function touch strip for track searching and for setting or triggering hot cues, in place of the tone arm.
User Guide, Manual Version 1.2, a 36 page multilingual document with English on pages 3 to 8 and Spanish on 9 to 14. The PDF was created on 31 October 2018 and last modified on 11 February 2019.
How big is it, and what does it draw?
368 x 413 x 90 mm and 9.3 kg, on an IEC inlet taking 100 to 240 V at 50/60 Hz and drawing 60 W. The platter is die cast aluminium, 13.1 inches or 332 mm, driven by a quartz direct drive motor.
Manuals. Official RANE manual page →
Broken link? Let us know and we'll fix it.
Where this sits in the line
- Next generation TWELVE MKII
Related turntables
Commonly paired with
What you usually find beside it in working booths, from club, festival and rental installs rather than from a manufacturer document.
Keep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy