Booth briefing. The Reloop Mixon 8 Pro is a four-channel hybrid DJ controller, which Reloop describe as a complete, balanced set of features for demanding professionals. It was developed from the ground up for Serato DJ Pro and Algoriddim djay Pro, with touch-sensitive jog wheels carrying real-time displays and two audio interfaces, so two laptops or a laptop and an iPad can hand over without a gap. Its mixer also takes outside sources, from turntables to microphones, so it works as a mixer on its own. It is a controller built for long, mixed-source sets.
When it goes wrong: The computer cannot see the controller No sound from the controller
Fast Lane
Mixon 8 Pro: equipment profile
Two computers, an iPad dock and a mixer that works on its own.
- Software
- Serato DJ Pro, unlocked by the hardware (from 3.0.6), and djay Pro on Mac, Windows, iPad and iPhone. DVS needs the Serato DVS expansion and is not available in djay Pro.
- Without a computer
- Mixes without a computer: two phono or line and two line inputs on RCA, two microphones (mic 1 on channel 3, mic 2 on channel 4), each channel switching between USB A, its analogue input and USB B.
- Sound out
- Balanced XLR and unbalanced RCA masters, a booth pair on 6.3 mm jacks, and headphones on 6.3 mm and 3.5 mm at the front.
- Power
- External 12 V, 3 A supply with grounding. A grounding screw on the back for turntables.
- Ports
- Two USB-B ports for two computers, plus a USB-C port for an iPad or iPhone, switched in on the USB A side. The dock on top takes a large tablet.
- Dimensions and weight
- 65.7 cm wide, 39.1 deep, 6.8 tall (25.9 × 15.4 × 2.7 in). 5.7 kg / 12.6 lb.
- Released
- No launch date published
Reloop Mixon 8 Pro instruction manual 244789_Reloop_IM, TECHNICAL SPECIFICATIONS, and the rear panel print.
The five things that decide your gig
The Mixon 8 Pro in five points, each linked to its section.
A microphone with no sound is usually on a channel not set to Mic. Mic 1 is channel 3, mic 2 is channel 4.
The manual names channel 1 in one place. The input switch is right.
A channel that will not cut with the crossfader has its assign switch on centre.
Push it to A or B and the crossfader works again.
An iPad on the USB-C port takes the A side, not the B side the manual describes.
Follow the print on the rear panel.
On Windows, Reloop say the ASIO driver is necessary.
Install it before the gig, not at the venue.
There is firmware for this controller, and the manual never mentions it.
Check the version on your unit before the gig.
Official equipment video
Note: This feature requires an internet connection.
If something goes wrong
No sound, or a channel that ignores the crossfader
Three things on the Mixon 8 Pro change what a channel does without anything on the screen telling you, so check them in this order before blaming the software.
Each channel has an input switch, and it has to point at the source that is actually playing: USB A, USB B or the analogue input on the back.
Each channel has an A, centre, B crossfader assign switch, and the centre position takes the channel off the crossfader, so it plays at its channel fader level whatever the crossfader does.
A channel that will not cut is usually sitting on centre.
A stereo/mono switch acts on the master output. Left on mono, a stereo system plays the same signal on both sides.
Out of a cold van into a warm room
The Mixon 8 Pro travels in a bag or a case between a van and a booth, and the manual gives you no waiting time to plan around.
All five manuals say not to operate the unit after bringing it from a cold environment into a warm one, and to wait until it reaches ambient temperature. No waiting time is given, so after a load-in from a cold van, let the unit warm up fully before switching it on.
What to watch for
Mic 1 is channel 3, whatever the next page says
On the Mixon 8 Pro, microphone 1 plays through channel 3 and microphone 2 through channel 4. The set up section and the input switch list of the English manual both say so, and the Mic On entry on the next page of the same manual lists them as channel 1 and channel 4. Go by the input switch: set channel 3 or 4 to Mic, raise that channel, and only then expect to hear the microphone.
Microphone 1 is a combo socket on the back for XLR or a 6.3 mm jack, microphone 2 is a 6.3 mm jack on the front, and each has its own talkover button.
Firmware exists, and the manual never mentions it
Compatibility
Serato DJ Pro, djay Pro and the Windows driver
Serato list the Mixon 8 Pro as unlocking Serato DJ Pro, and announced support in Serato DJ Pro 3.0.6 on 15 May 2023. Control vinyl or control CDs need the paid Serato DVS expansion, Pitch Play needs Pitch ’n Time and Saved Flip needs Flip.
In djay Pro the pads carry Neural Mix controls, and switching the EQ between conventional bands and Neural Mix elements needs djay Pro 4.1.10 or higher. Reloop note that DVS is not available with djay Pro on this controller.
On Windows Reloop say an ASIO driver is necessary, and the product page offers two versions, v5.72.0 and v6.0.0, both for Windows 10 and 11.
Two computers, an iPad, and the switch between them
Two USB-B ports, A and B, take two computers, so a changeover happens channel by channel by moving each input switch from USB A to USB B. The switch that brings in an iPad or iPhone on the USB-C port is printed on the rear panel inside the USB A group, while the manual describes it as choosing for the B port. Go by the panel: with that switch on iOS, the USB-C device takes the A side and the USB-B A socket is out of the chain.
The docking station takes up to a 12.9 inch iPad Pro, and the USB-C port supports newer iPad and iPhone models including power delivery.
Features explained
A mixer without a computer
The Mixon 8 Pro is built as a hybrid: with a laptop or an iPad it is a Serato DJ Pro or djay Pro controller with its own audio interface, and with nothing connected its mixer section still mixes the analogue inputs.
It mixes without a computer. Channels 1 and 2 take phono or line on RCA, channels 3 and 4 take line on RCA, and every channel has an input switch that chooses between USB A, its analogue input and USB B. Channels 3 and 4 add a microphone position.
The FX paddles, which latch one way and spring back the other
Four FX paddles, one per channel. Pushed forward the effect latches on, pulled back it plays only while held, and centre is off. FX unit 1 serves decks 1 and 3, FX unit 2 decks 2 and 4.
If an effect is still running after you let go, the paddle is locked forward, and returning it to centre is what stops it.
Jog wheels, vinyl mode and the pitch range
The jog wheels are 149 mm with displays showing the deck, USB A or B, time, BPM, pitch and pitch range. Vinyl mode is Shift and Slip, and with vinyl mode off the jog only bends the pitch.
A jog that nudges but will not scratch is the symptom, and turning vinyl mode back on is the cure.
Shift and Silent Cue change the pitch range: plus or minus 8, 16 and 50 per cent in Serato DJ Pro, and 8, 10, 25, 50 and 75 per cent in djay Pro. The manual names that button Silent Cue in its heading and Censor in the Shift line beneath it.
Shift and Time switch the deck to reverse play, and holding Key Lock for longer resets the tempo to the track’s original speed.
The sampler is not the same in both programs
The sampler differs by software: Serato DJ Pro gives 8 slots with banks A to D, while djay Pro gives 16, eight per side, and shows its sampler view only in 2 deck view.
Connections and setup
What is on the back and on the front
On the back, from the XLR end: balanced XLR master 1, RCA master 2, a booth output on two 6.3 mm jacks, line in for channel 4, phono or line in for channel 2 with its switch, the grounding screw, phono or line in for channel 1 with its switch, line in for channel 3, the USB B port, the USB A port with the USB-C port and its switch, power, the power supply socket and the microphone 1 combo socket.
On the front: two headphone sockets, 6.3 mm and 3.5 mm, the microphone 2 jack and the crossfader curve knob.
Power, and the order to switch on
An external 12 V, 3 A power supply, which Reloop describe as a supply with grounding. The manual tells you to switch on only with the master and booth controls at minimum.
The output figures, as printed
Reloop rate the balanced master at 4 dBu with the volume at 2 o’clock and 14 dBu maximum, distortion under 0.01 per cent, and print its signal to noise ratio as less than minus 85 dB. The unbalanced master is rated at 6 dBV, 16 dBV maximum. The booth output carries the same figures as the balanced master, except that its signal to noise line prints a stray symbol in front of 85 dB.
Those figures are reproduced as printed. A signal to noise ratio written as less than minus 85 dB reads inverted, and this page does not rewrite a manufacturer number into the one it probably meant.
Firmware, drivers and manuals
Official downloads and documents
Go to Reloop for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
Manuals. Official Reloop manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
How big is it, and what does it weigh?
657 x 391 x 68 mm, width by depth by height. 5.7 kg
What comes in the box?
The controller, the manual, a USB-A to USB-B cable and the 12 V, 3 A power supply.
Playing soon and it is not working?
Emergency Mode walks you through the checks in order, and it works with no signal once you have opened it.
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy