Booth briefing. The DJ-202 is the compact model in Roland's family of Serato DJ controllers, a two-channel, four-deck controller for Serato DJ Lite. Roland says it preserves the concept of the DJ-808 and the DJ-505 in a smaller unit. It has drum kits from the TR-909, TR-808, TR-707 and TR-606 built in, an onboard sequencer that drives the Serato sampler, large low-latency platters and a mic input with effects. It is for DJs who also build beats live or in the studio. It has no player of its own, so it plays nothing without a laptop running Serato.
When it goes wrong: The computer cannot see the controller No sound from the controller
Fast Lane
DJ-202: equipment profile
Roland's compact two-channel, four-deck Serato DJ controller, with built-in drum kits and a mic input.
- Software
- Serato DJ Lite, which can be upgraded to Serato DJ Pro. The manual is written for Serato DJ Intro.
- What it unlocks
- Startup Guide and USB cable. Driver and DJ software are downloads.
- Without a computer
- Nothing. No media slot, library or internal player.
- Sound out
- MASTER OUT: RCA pair, unbalanced, nominal 2.0 Vrms. PHONES: stereo quarter-inch. MIC IN: quarter-inch. MIDI OUT.
- Power
- USB bus power, 500 mA. No adaptor.
- What the computer needs
- One PC port, USB type B. Roland driver required.
- Dimensions and weight
- 47.8 cm wide, 29.7 deep, 6.2 tall (18.8 × 11.7 × 2.4 in). 2.1 kg / 4.6 lb.
- Released
- 2017
Roland's own DJ-202 specification page, the owner's manual and the update history to ver. 1.14.
DJ-202: five things to know
The DJ-202 in five points, each linked to its section.
No line or phono inputs, only one mic jack.
Nobody can plug in behind you.
The only output is unbalanced RCA.
The monitor comes off the same pair as the room.
Two downloads are needed before it plays.
Opened at a venue with no internet, it cannot play.
The laptop powers it, so there is no adaptor.
A weak laptop port can take the music down.
Below firmware 1.11 the drum section fails with current Serato.
On a used unit, read the version first.
Official equipment video
Note: This feature requires an internet connection.
Connections and setup
What you can plug into it
Short answer. The DJ-202 takes one microphone on a quarter-inch MIC IN jack, and nothing else. Roland's specification page lists five connectors in total and none of the others is an audio input.
What that rules out. No turntable, because there is no phono input and no ground post. No CDJ or second laptop, because there is no line input. No feed from the house mixer. The music comes from the computer or it does not come at all.
Changeover. External inputs are ordinary on a DJ controller, so somebody who has used one arrives expecting a spare channel to hand to the next person. On this unit a changeover means unplugging.
Mic. There is a MIC SENS knob, a low-cut filter and a noise gate for the mic path, all in the system settings, so it is a working microphone channel rather than an afterthought.
Outputs and level
Short answer. MASTER OUT on a pair of RCA phono jacks, unbalanced, at a published nominal level of 2.0 Vrms. PHONES is a stereo quarter-inch jack. There is no XLR.
Level. Roland publishes a level for the DJ-202, which is rare for the brand, so the channel can be set from the figure at soundcheck rather than by ear.
Long cable runs. RCA has no noise rejection, so a long run to a stage box picks up whatever the room is doing. Keep the run short, or put a DI or a balancing box between the unit and the wall.
No booth output. The monitor shares the master. Whatever the room hears, the booth hears, at the same level the master fader sets.
What the computer needs
Short answer. One PC port on USB type B, Roland's own driver, and Serato. The box holds a Startup Guide and a USB cable, and the manual states that the driver and the DJ software are not included.
USB type B. The older square connector. A laptop with only USB-C needs an adaptor or a B-to-C cable, and that cable is not supplied with the computer either.
Driver. A separate download from the system program. Roland publish driver versions to 1.0.6 for macOS Sonoma 14 or later and 1.0.2 for Windows 10 and 11, alongside older builds for older systems. A unit that appears in the DJ software but produces no sound is usually the driver.
Software. Serato. The manual on Roland's site names Serato DJ Intro. That was the name at the time; the current free tier is Serato DJ Lite, which Roland confirmed in March 2018. The unit can be upgraded to Serato DJ Pro.
Power and weight
Short answer. USB bus power at 500 mA. There is no AC adaptor for this unit and no DC input on it.
No power supply. Nothing to pack or forget at the last venue, and one cable to carry. On a unit this size that is most of the reason to own it.
Single point of failure. One cable carries audio, control and power together, so a marginal laptop port, a hub that cannot supply 500 mA or a worn cable takes the music down rather than just the lights. Plug into the computer directly, not through a hub.
Weight. 2.1 kg. Lighter than anything else in this part of the Roland hub, and the whole rig fits one shoulder bag.
What to watch for
The two faults Roland names
Short answer. The DJ-202 has two named faults in eight years of releases, and both are about the software seeing the unit wrongly rather than the unit itself failing.
1.11, July 2019. The TR-S drum section failed to work correctly with Serato DJ Pro 2.1.1 and later. The DJ-505 carries the same fault at the same version number in the same month, which is unusual: Roland version numbers rarely line up across models.
1.03, October 2017. VINYL for decks 3 and 4 could not be turned off from the software.
1.10, January 2018. The release that changes what the unit can do: Backspin Length, jog-dial top-surface sensitivity, TR-606 and TR-707 sounds, the TR-S kit count raised from 8 to 12, and the BPM range widened from 40-300 to 5-500.
Other releases. 1.04 says only that minor bugs have been fixed. 1.12, 1.13 and 1.14 are version-number changes Roland attributes to management circumstances, with specifications unaffected.
Professional tips
Before the gig
Carry RCA-to-XLR and RCA-to-quarter-inch leads. A venue wired for XLR needs an adaptor, and two cheap cables mean the house can always take it.
Ask about the changeover before you accept the booking. Agree how it will work, or bring a small mixer.
Install the driver and the software at home. See What the computer needs.
Plug straight into the computer. A hub is the weak link, as the power section explains.
Firmware, drivers and manuals
Official downloads and documents
Go to Roland for the files themselves. We link their pages instead of hosting a copy, because a manual copied here is a snapshot of release day and theirs is the one that stays current.
The system program and the driver are separate downloads, and the version of record is 1.14. Roland also publish the Startup Guide and the owner's manual in eight languages.
Firmware downloads. Official Roland firmware page →
Manuals. Official Roland manual page →
Broken link? Let us know and we'll fix it.
Frequently asked questions
Quick answers
- Can I connect a turntable to a DJ-202?
- No. Nothing on it accepts a turntable.
- Can I plug a CDJ or a second laptop into it?
- No. The computer and the microphone are its only sources.
- What cable do I need to connect it to the house system?
- A lead with RCA plugs at the unit end, and whatever the house needs at the other.
- What output level does it run at?
- 2.0 Vrms nominal at MASTER OUT.
- Does it have a booth output?
- No. The room and the monitor share the master pair.
- Does it need a power supply?
- No. One USB cable from the computer does it all.
- Will it play without a computer?
- No. It has no media slot, library or internal player.
- Which firmware should it be on?
- 1.11 or later. The version of record is 1.14.
- Which software does it use?
- Serato DJ Lite, or DJ Pro after an upgrade.
- Can the pads control a TR-8S?
- No. Roland names the DJ-202 as unable to do that. The pads play its own TR-S section.
Playing soon and it is not working?
Start Emergency ModeKeep the Emergency Card
We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.
Register and receive itRegistering is free and counts everywhere on Save My Gig. We send a confirmation email first. Your address is stored with Brevo, our email provider. Unsubscribe any time. Privacy
Sources: Roland's product pages and owner's manual for the DJ-202, and its published update history, checked 16 October 2026. Specifications theirs, priorities ours.