Released 2024 Reviewed: 7 November 2026

RANE PERFORMER, field manual

RANE PERFORMER four channel motorised DJ controller for Serato, top view with two platters and four channel strips

Booth briefing. The RANE PERFORMER is a four-channel Serato DJ Pro controller with RANE's industrial build quality and sound, and motorised platters under the hands. Two platters drive the software decks, while rear inputs feed the other two channels, so a turntable, a CD player or any line source can join the mix. It unlocks Serato DJ Pro while connected, with no separate licence. For a DJ it combines the moving-platter feel of the RANE ONE with a four-channel mixer, which suits longer sets and open-format nights that mix software and outside sources.

Fast Lane

PERFORMER: equipment profile

A four-channel motorised Serato controller with two platters, a MagFour crossfader and sixteen pads.

Software
Serato DJ Pro. Cirrus Logic converters, 24-bit PCM at 48 kHz, 113 dB on both converters.
What it unlocks
Activates Serato DJ Pro while connected. VirtualDJ runs with a separate VirtualDJ Pro licence.
Without a computer
Nothing plays without a computer. Two RCA pairs, line or phono, feed decks 3 and 4, plus two combo mic inputs.
Sound out
Main on XLR at 8 Vrms and on RCA at 4 Vrms. Booth on quarter-inch at 8 Vrms.
Output level
Headphones 4 Vrms unloaded and 50 mW into 50 ohms, on both jack sizes. Outputs flat from 20 Hz to 20 kHz.
Power
IEC inlet, 100 to 240 V at 50/60 Hz, 150 W consumed.
What the computer needs
Two USB Type-B ports, so two laptops stay connected.
Released
2024

RANE PERFORMER User Guide v1.5 and its Technical Specifications table.

The five things that decide your gig

The PERFORMER in five points, each linked to its section.

Install the driver before the firmware updater.

On a borrowed laptop the updater opens and finds nothing.

The firmware history, and the order that matters

Four channels, but only two platters.

Decks 3 and 4 are whatever you plug in.

The deck arithmetic, and what has no platter

A channel set to Line goes half dead.

It reads as a fault, but it is a documented limit.

Line mode, and what stops working

Booth is on quarter-inch jacks, not XLR.

A cable built for an XLR booth output will not plug in.

The rear panel, item by item

Firmware 1.3.0.13 fixed two FX faults.

On an older build both can happen mid set.

The four builds, and what each admitted

Official equipment video

Note: This feature requires an internet connection.

Features explained

Four channels, two platters

Four channels but two platters. Decks 1 and 2 are the software decks under the platters. Decks 3 and 4 are fed from the rear RCA inputs and have no platter of their own, so an external turntable, CD player or line source plays on them. With the DVS plugin, which RANE state is bought separately from Serato, those two can be driven by Serato control vinyl or control CDs instead.

RANE describe high torque motorised platters with full colour jog displays, and each platter centre carries a 3.5 inch full colour LCD. Torque is switchable between LOW and HIGH in the utility menu, and the feel is changed mechanically by combining the plastic and felt slip rings. No RANE document found publishes a platter diameter.

The licence, the FX and the stems

RANE state the PERFORMER activates Serato DJ Pro and serves as the licence for as long as it is connected to the computer, so there is no separate Serato purchase. VirtualDJ is supported but needs a VirtualDJ Pro licence bought separately.

A hardware FX engine with 29 effects, among them Reverb, Echo, Fader Tone, Choppa and Mute, driven from six FX buttons whose assignments are stored in the unit and recalled after a power cycle. Serato DJ Pro’s own software FX are available alongside them.

Stem Split separates a track’s vocal and instrumental across two channels. Stem Level remaps the EQ knobs onto stem elements, High for vocals, Mid for melody and bass, Low for drums. There are dedicated Acapella and Instrumental buttons and a Stems pad mode.

A Mag 4 crossfader, user replaceable, with an external tension knob; its curve and reverse controls are on the front panel. The channel faders are RANE’s Precision Feel design with adjustable tension, and their curve and reverse options live in the utility menu.

Connections and setup

The rear panel, item by item

Rear panel, in RANE’s own order: two mic inputs on XLR / 6.35 mm TRS combo jacks, two stereo RCA deck phono/line inputs, a line/phono selector per deck, a phono ground terminal, main out on RCA, main out on XLR, booth/zone on balanced 6.35 mm TRS, a stereo/mono switch for the main outs, two USB Type-B ports, the power input and the power button. Headphones are on 6.35 mm and 3.5 mm at the front.

RANE’s own specification table also prints a booth row on XLR, which is a template fault: the connector list in the same document and the rear panel itself both say quarter-inch.

Both mic inputs have their own gain, a two band EQ and an on/off control. Mic 1 carries two things mic 2 does not: an Echo knob, and Talkover, which ducks the main mix while you speak.

Two USB ports, and the handover

Two USB Type-B ports, which RANE say allow connecting multiple computers at once so one DJ can hand over to the next without unplugging anything. Both machines running Serato at the same time, and how the audio channels are divided: N/A.

Compatibility

Line mode, and what stops working

Channels 3 and 4 each have a two-way USB/LINE switch. On LINE the channel plays whatever is wired to its rear RCA input rather than the software deck.

Serato Channel FX apply to the software decks and not to external sources. Set a channel to Line and the Channel FX do nothing to it. The Filter still works on a line input, which is why the channel can feel half dead rather than completely dead.

Standalone, requirements and size

Standalone operation: N/A. The unit is presented throughout as a controller for a computer running Serato DJ Pro, so bring a laptop.

Computer requirements follow Serato's own minimum requirements article, so they move when Serato move them.

783.3 x 402.3 x 109.7 mm and 12.8 kg, which is RANE’s own figure and makes it a two-person lift into a booth rather than a one-hand carry.

What to watch for

The firmware history, and what 1.3.0.13 fixed

The PERFORMER is on firmware 1.3.0.13, released 3 April 2025, and that was still the published build when last checked.

Four builds in RANE’s own release-note history. 1.0.0.57 is the initial mass production firmware and carries no date. 1.1.0.13 on 25 June 2024 is the first dated update. 1.2.0.10 followed on 29 October 2024, and 1.3.0.13 on 3 April 2025.

What 1.3.0.13 changed, in RANE’s words: the same effect can now be saved to multiple FX buttons with different parameters; Mic 1 gained a Reverb effect alongside Echo, with room size, pre-delay and depth; and a new ACAP/INST FX menu option swaps the primary and secondary functions of the Acapella and Instrumental buttons so stem FX fire without holding Shift. The fixes name real faults: album artwork not always showing in the wheel displays, holding Shift and pressing another FX button changing the beat division of the effect already selected, and the hardware and software FX button falling out of sync with Serato DJ Pro.

RANE do not print the version on the pages a reader would actually reach. The support FAQ and the firmware walkthrough both say only that an update is required and that the updater is a separate application per platform.

If something goes wrong

The updater cannot see the unit

RANE are explicit about the order, and getting it wrong looks like a broken unit rather than a missed step: install the driver first or the firmware update application will not recognise your RANE PERFORMER. Drivers ship bundled with Serato DJ Pro and are also on RANE’s downloads page. During the update itself RANE warn not to disconnect the unit from the computer or its power source.

Frequently asked questions

What is it, and which document says so?

RANE call the PERFORMER a motorised DJ controller for Serato DJ Pro, and their product page claims it as the only 4-channel motorised DJ controller built to RANE’s standards. Four mixer channels, two motorised platters.

User Guide, Manual Version 1.5. Document created 31 May 2024, last modified 2 April 2025.

Manuals. Official RANE manual page →

Broken link? Let us know and we'll fix it.

Keep the Emergency Card

We will email you the printable PDF so it is on your phone before the next dark booth. Occasional notes that save gigs. No spam, unsubscribe in one click.

Register and receive it